Marantz SR6010 - Page 95

Sound modes and surround parameters
Sound mode
Surround Parameter
Dialog Level Adjust
Subwoofer Level
Adjust
Cinema EQ
Loudness
Management
z1
Dynamic
Compression
z2
Dialog Control
z3
L ow Frequency
z4
Speaker Select
Direct/Pure Direct (2-channel) z5 Sz6 SS
Direct/Pure Direct (Multi-channel) z5 SS SS S
DSD Direct (2-channel)
Sz6
DSD Direct (Multi-channel) z5 SS S
Stereo
S SS
Multi Ch In
SSS S
Dolby Surround
SSSSS
DTS Neural:X
SSS S
Audyssey DSX®
SSSSS S
Dolby Digital
SSSSS S
Dolby Digital Plus
SSSSS S
Dolby TrueHD
SSSSS S
Dolby Atmos
SSSSS S
DTS Surround
SSS S S
DTS 96/24
SSS S
DTS-HD
SSS S
DTS Express
SSS S
DTS:X
SSS SS
Multi Ch Stereo
SS SS SS
Virtual
SS SS S
z
1 -
z
6 : “Sound modes and surround parameters” (
v
p. 290)
Contents Connections Playback Settings Tips Appendix
288
Front panel Display Rear panel Remote Index
Sound mode
Surround Parameter
Tone
z7
Audyssey
M-DAX
z10
Center Spread DTS Neural:X
MultEQ® XT32
z8
Dynamic EQ
z9
Dynamic
Volume
z9
Audyssey
LFC™
z9
Audyssey
DSX®
Direct/Pure Direct (2-channel) z5
Direct/Pure Direct (Multi-channel) z5
DSD Direct (2-channel)
DSD Direct (Multi-channel) z5
Stereo
SSSSS S
Multi Ch In
SSSSSS
Dolby Surround
S SSSSS S
DTS Neural:X
SSSSS S
Audyssey DSX®
SSSSSS
Dolby Digital
SSSSSS
Dolby Digital Plus
SSSSSS
Dolby TrueHD
SSSSSS
Dolby Atmos
SSSSS
DTS Surround
SSSSSS
DTS 96/24
SSSSSS
DTS-HD
SSSSSS
DTS Express
SSSSSS
DTS:X
SSSSSS
Multi Ch Stereo
SSSSS S
Virtual
SSSSS S
z
5,
z
7 -
z
10: “Sound modes and surround parameters” (
v
p. 290)
Contents Connections Playback Settings Tips Appendix
289
Front panel Display Rear panel Remote Index
z1
This item can be selected when a Dolby Digital, Dolby Digital Plus, Dolby TrueHD or Dolby Atmos signal is played.
z2
This item can be selected when a Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS:X or DTS signal is played.
z3
This item can be selected when a DTS:X signal that is compatible with the Dialog Control function is input.
z4
This item can be selected when a Dolby Digital or DTS signal or DVD-Audio is played.
z5
During playback in Pure Direct mode, the surround parameters are the same as in Direct mode.
z6 This setting is available when “Subwoofer Mode” in the menu is set to “LFE+Main”. (v
p. 230)
z7 This item cannot be set when “Dynamic EQ” is set to “On”. (v
p. 181)
z8
This item cannot be set when Audyssey
®
Setup (Speaker Calibration) has not been performed.
z9
This item cannot be set when “MultEQ
®
XT32” in the menu is set to “Off”. (v p. 180)
z10
This item can be set when the input signal is analog, PCM 48 kHz or 44.1 kHz.
Contents Connections Playback Settings Tips Appendix
290
Front panel Display Rear panel Remote Index
95