Marantz SR9200 Service Manual (English)

Other manuals for Marantz SR9200

Service Manual145 pages

Specifications2 pages

Questions and Answers:

M
meghanharrisonAug 21, 2025
Why is there no sound output from the center speaker on my Marantz Receiver?
- T
  Todd BennettAug 21, 2025
  If no sound is coming from the center speaker of your Marantz Receiver, first check the center speaker cable connection to ensure it is correctly connected. Also, if 'STEREO' is selected for Surround mode, no sound will be output from the center speaker, so set another Surround mode. Finally, verify that 'Center = NONE' has not been selected in SETUP mode and make the correct setting.
T
Tammy GomezAug 23, 2025
Why is there no sound from the surround speaker on my Marantz Receiver?
- L
  Lisa ComptonAug 23, 2025
  If you're not getting any sound from the surround speaker of your Marantz Receiver, check that the surround speaker cable is properly connected. Also, if STEREO is selected for Surround mode, no sound will be output from the surround speaker; select a different Surround mode. Finally, verify that 'Surround = NONE' has not been selected in SETUP mode and make the correct setting.
R
Renee WongAug 25, 2025
Why is there no sound output from the surround back speaker on my Marantz SR9200?
- E
  elizabeth19Aug 25, 2025
  If there's no sound from the surround back speaker on your Marantz Receiver, ensure the speaker cable is correctly connected. If 'STEREO' is selected for Surround mode, no sound will be output from the surround speaker. Also, if 'Surr. Back = NONE' has been selected in SETUP mode, change the setting. The surround back channel is only active in THX surround EX mode, so set the receiver to THX Surround EX mode.
S
Susan ColonAug 26, 2025
Why is there no output to the Sub Woofer Out on my Marantz SR9200?
- A
  alicia63Aug 27, 2025
  If there is no output to the Sub Woofer Out on your Marantz Receiver, check if 'Sub-woofer = NONE' has been selected in SETUP mode. If so, select 'Sub-woofer = YES'.
T
thomas59Aug 27, 2025
What to do if my Marantz SR9200 Receiver has no sound and picture even when power is on?
- B
  burkecourtneyAug 27, 2025
  If your Marantz Receiver has no sound and picture when powered on, the issue might be due to several reasons. First, check if mute is activated and deactivate it using the remote. Next, ensure the input cables are correctly connected as per the connection diagram. Also, verify that the master volume isn't turned all the way down and that the function selector is in the correct position.
C
Christina GriffinAug 29, 2025
Why is noise heard during FM reception on my Marantz SR9200 Receiver?
- S
  Sheila SchaeferAug 29, 2025
  If you're experiencing noise during FM reception with your Marantz Receiver, it could be due to weak radio waves from the broadcasting station. Try installing an FM outdoor antenna or using cable TV/FM to improve reception.
J
johnshawAug 30, 2025
Why am I getting sound and pictures from equipment other than what's selected with the function selector on my Marantz SR9200?
- A
  Amber SimpsonAug 30, 2025
  If your Marantz Receiver is outputting sound and pictures from equipment different from what you've selected, the input cable might be connected incorrectly. Refer to the connection diagram to ensure the cable is properly connected.
V
Victoria HowardSep 1, 2025
Why is sound from the wrong channel output from the speaker on my Marantz SR9200 Receiver?
- M
  Mark BowersSep 1, 2025
  If sound from the wrong channel is being output by the speaker on your Marantz Receiver, the speaker cable may be connected incorrectly. Refer to the connection diagram to ensure the cable is connected correctly.
E
Eric Ellis Jr.Sep 3, 2025
Why can't I change the surround mode on my Marantz SR9200 Receiver?
- J
  Jesse EllisSep 3, 2025
  If you cannot change the surround mode on your Marantz Receiver, it might be because headphones are connected to the jack. Disconnect the headphones, as the surround mode will be fixed to STEREO when headphones are connected.
A
annawilliamsSep 4, 2025
Why is noise produced during DTS-encoded CD or laser disc play on my Marantz Receiver?
- R
  Robin GreenSep 4, 2025
  If you're experiencing noise while playing a DTS-encoded CD or laser disc on your Marantz Receiver, and 'Analog' has been selected for input, be sure to perform a digital connection, select digital input, and then play the disc.

Marantz SR9200 Specifications

General

Brand	Marantz
Model	SR9200
Category	Receiver
Language	English

Marantz SR9200 User Guide

Table of Contents

Other manuals for Marantz SR9200

Questions and Answers:

Marantz SR9200 Specifications