22
To replace batteries:
• Slide belt clip to the left to remove.
• Press tab down on battery cover and pull out.
• Install 2 “AAA” Alkaline batteries. Check positive (+) and negative (-) symbols, on the case and bat-
tery, to insure proper installation.
• Replace the battery cover.
• Remove batteries before storing remote control.
To test frequency range:
• Turn unit on.
• Use remote to turn light on and o as you move away from unit.
• Remote control is out of frequency range when light will no longer turn on and o.
IMPORTANT
• Do not leave remote control exposed to sunlight for prolonged periods of time.
• Remote control has frequency range of up to 100ft (30m).
• Test frequency range before and during use.
TROUBLESHOOTING
If the remote is not working properly or not interfacing correctly with the controller, it may be due to
weak batteries, batteries being incorrectly installed or the remote is not correctly linked to controller.
Possible solutions
• Replace batteries and install according to image in battery housing.
• Link remote and controller by:
a. Turn Controller & Remote “ON”,
b. Press and HOLD “SET TEMP” on controller for 3 seconds.
c. On the Remote press “MEAT PROBE”, “LIGHT”, “MEAT PROBE”, “LIGHT” (all buttons must be
pressed within 5 seconds of each other). A short beep will occur after each button press.
THE INFORMATION
CONTAINED IN THIS
DRAWING IS THE SOLE
PROPERTY OF
MASTERBUILT
MANUFACTURING.
ANY
REPRODUCTION IN
PART OR AS A WHOLE
WITHOUT THE WRITTEN
PERMISSION OF
MASTERBUILT
MANUFACTURING IS
PROHIBITED.
Masterbuilt Manufacturing, Inc.
General Tolerance
X.
X.X
X.XX
X.XXX
X/X
Degree
METRIC
1
0.80
0.40
0.10
N/A
1°
Unless Otherwise Specified
1 Masterbuilt Ct
Columbus, GA 31907
Phone: 706-327-5622 Fax: 706-256-5485
Revision
Description
Date
STANDARD
N/A
0.030
0.015
0.005
1/32
1°
DATE:
DWG Name
GENERAL DRAWING NOTES:
1. BREAK SHARP EDGES .003-.010 INCHES (.08-.25 MM)
2. DIMENSIONS SHOWN ARE IN INCHES [MM]
DO NOT SCALE DRAWING
TITLE:
REV: --
SCALE: 1:1
--
SHEET 1 OF 1
Default
DRW.BY:
4. WEIGHT: --
Adam Carter
4/28/2010
3. MATERIAL: --
THE INFORMATION
CONTAINED IN THIS
DRAWING IS THE SOLE
PROPERTY OF
MASTERBUILT
MANUFACTURING.
ANY
REPRODUCTION IN
PART OR AS A WHOLE
WITHOUT THE WRITTEN
PERMISSION OF
MASTERBUILT
MANUFACTURING IS
PROHIBITED.
Masterbuilt Manufacturing, Inc.
General Tolerance
X.
X.X
X.XX
X.XXX
X/X
Degree
METRIC
1
0.80
0.40
0.10
N/A
1°
Unless Otherwise Specified
1 Masterbuilt Ct
Columbus, GA 31907
Phone: 706-327-5622 Fax: 706-256-5485
Revision
Description
Date
STANDARD
N/A
0.030
0.015
0.005
1/32
1°
DATE:
DWG Name
GENERAL DRAWING NOTES:
1. BREAK SHARP EDGES .003-.010 INCHES (.08-.25 MM)
2. DIMENSIONS SHOWN ARE IN INCHES [MM]
DO NOT SCALE DRAWING
TITLE:
REV: --
SCALE: 1:1
--
SHEET 1 OF 1
Default
DRW.BY:
4. WEIGHT: --
Adam Carter
4/28/2010
3. MATERIAL: --
HOW TO USE CONTROL PANEL & REMOTE CONTROL
CAUTION
• Keep batteries away from small children. If battery is swallowed consult a physician immediately.
•
Be sure to insert batteries correctly. Improper installation may result in leaks and/or possible explosion.
• Do not dispose of batteries in re.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh,etc) batteries.
*Batteries not
included
To Next Page
Loading...
Need help?
General
