WARNING!
• Use the proper extension cord. Make sure to use an extension cord that is heavy enough to carry
the current required by the tool. An undersized cord will cause a drop in line voltage, resulting in
loss of power and overheating of the tool.
• Use the extension cord only for intended purpose. Do not pull the extension cord to remove it
from the power socket.
CAUTION!
In all cases, verify that the outlet in question is properly grounded. If you are not sure, have a
licensed electrician check the outlet.
11
SAFETY GUIDELINES
10
SAFETY GUIDELINES
USE SAFETY GOGGLES AND EAR PROTECTION:
ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH CUL REQUIREMENTS. FLYING
DEBRIS can cause permanent eye damage.
The tool is loud and the sound can cause hearing damage. Always wear ear protection to help
prevent hearing damage and loss. Failure to comply may result in moderate injury.
USE DUST MASK:
Some dust created by sawing contains chemicals that are known to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals come from lead-based paints,
crystalline silica from bricks, cement and other masonry products, arsenic and chromium from
chemically treated lumber. To reduce exposure to these chemicals, work in a well-ventilated
area with approved safety equipment, such as dust masks that are specially designed to filter out microscopic
particles.
POSITION OF TILE SAW
• To avoid the possibility of the appliance plug or
receptacle getting wet, position tile saw to one side of
a wall-mounted receptacle to prevent water from
dripping onto the receptacle or plug. The user should
arrange a "drip loop" in the cord connecting the saw
to a receptacle. The "drip loop" is the part of the cord
below the level of the receptacle, or the connector if
an extension cord is used, to prevent water traveling
along the cord and coming into contact with the
receptacle.
• If the plug or receptacle does get wet, DON’T unplug
the cord. Disconnect the fuse or circuit breaker that
supplies power to the tool. Then unplug and examine for presence of water in the receptacle.
ELECTRICAL SAFETY
GUIDELINES FOR USING EXTENSION CORDS:
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current
to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. The conductor with
a green outer surface, with or without yellow stripes, is the
equipment-grounding conductor. If repair or replacement
of the electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service technician if
the grounding instructions are not completely understood,
or if in doubt as to whether the tool is properly grounded.
Use only three-wire extension cords that have three-prong
grounding plugs and three-pole receptacles that accept
the tool’s plug, as shown in Fig. 2. Repair or replace a damaged or worn cord immediately.
GROUNDING INSTRUCTIONS:
• Make sure the extension cord is in good condition. When using an extension cord, be sure to use one
that is heavy enough to carry the current that your product will draw. An undersized cord will cause a
drop in line voltage, which will result in loss of power and overheating. The table on the next page shows
the correct size to be used according to cord length and nameplate ampere rating. When in doubt, use
the next heavier gauge. The smaller the gauge number, the heavier the cord.
• Make sure your extension cord is properly wired and in good condition. Always replace a damaged
extension cord, or have it repaired by a qualified person before using it. Protect your extension cords from
sharp objects, excessive heat, and damp or wet areas.
• Use a separate electrical circuit for your tools. This circuit must consist of not less than #12 wire with a
20 A time-delayed fuse or a #14 wire with a 15 A time-delayed fuse. Before connecting the motor to the
power line, make sure the switch is in the Off position and the electric current is rated the same as the
current stamped on the motor nameplate. Running at a lower voltage will damage the motor.
Tool
Drip loop
Fig. 1
Supporting surface
Power supply
cord
Fig. 2
Three-prong plug
Grounding prong
Properly grounded outlet
model no. 055-6778-4 | contact us 1-800-689-9928
To Next Page
Loading...
