MasterForce MFX2U2200 - User Manual

MasterForce MFX2U2200

20 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Electric Pressure Washer

MFX2U2200

261-1671

OPERATOR’S MANUAL

To Reduce The Risk Of Injury, User Must

Read And Understand Operator's Manual. Save These

Instructions For Future Reference.

CAUTION:

96048_IM_MFX2U2200.indd 196048_IM_MFX2U2200.indd 1 2020/12/10 上午10:402020/12/10 上午10:40

Table of Contents

Questions and Answers

D
Donald ShortAug 7, 2025
What to do if MasterForce MFX2U2200 turns on for 2 seconds then shuts off?
- B
  benjaminhesterAug 7, 2025
  When the water is connected, the accessories are assembled properly, and the power is turned on, the MasterForce pressure washer may turn on for 1 - 2 seconds to prime the pump. It automatically shuts off and waits for the spray gun trigger to be pressed. When the trigger is pressed, water starts flowing through the pump. The water sensor in the pump 'senses' the moving water and automatically turns the pressure washer on. If this doesn't solve the issue, turn the power off, hold in the trigger on the spray gun so that you have a steady stream of water, and while holding the trigger open, simultaneously turn the power on.
A
Alexander GonzalezAug 17, 2025
Why is my MasterForce MFX2U2200 leaking at the hose connection?
- N
  Natalie MullenAug 17, 2025
  If your MasterForce Pressure Washer is leaking where the high-pressure hose connects to the spray gun, ensure there is an o-ring at the end of the metal tip of the high-pressure hose. If the o-ring is missing, the connection will leak. An O-Ring Replacement Kit is included with your purchase. You can find additional O-Ring Kits online.
L
lesliedukeAug 27, 2025
What to do if MasterForce MFX2U2200 unit is running, but there is no water flow?
- M
  moniquejohnsonAug 28, 2025
  If your MasterForce pressure washer is running but not dispensing water, first ensure that power is not turned on until water comes through the spray gun, as doing so can damage the motor. Then, check the water source, eject the nozzle from the lance to see if the clog is there (if it is, follow nozzle cleaning instructions), remove the lance to spray directly from the spray gun to identify lance problems, and inspect the Garden Hose Adapter for loose connections and filter for debris.

Summary

Safety Instructions

Ground Fault Circuit Interrupter Protection

Explains the function and importance of the GFCI for electrical safety.

Preparation

Tools Required for Assembly

Lists necessary tools for assembling the pressure washer unit.

Assembly Instructions

Frame Assembly

Details the initial assembly of the pressure washer frame and wheels.

Locking Spray Gun

Explains how to safely lock the spray gun trigger to prevent accidental discharge.

Extension Lance Installation

Instructions for attaching and detaching the extension lance to the spray gun.

Foam Cannon Installation

Guide on how to connect and use the foam cannon for detergent application.

Foam Cannon Storage

Proper methods for storing the foam cannon after use.

Operating Instructions

Adjusting Soap Levels on Foam Cannon

How to adjust the detergent concentration for the foam cannon.

How to Avoid Damaging Surfaces

Guidance on using the pressure washer to prevent surface damage.

Operation Tips

General advice and best practices for operating the pressure washer.

Using Power Cord

Instructions for managing and using the power cord safely and effectively.

Care and Maintenance

Detergents

Information on selecting and using detergents with the pressure washer.

Cleaning Nozzles

Steps to clean clogged or partially clogged spray nozzles for optimal performance.

Cleaning Garden Hose Adapter

How to clean the screen inside the garden hose adapter.

Storage

Procedures for properly storing the pressure washer.

Pump Saver

Pump Saver Instructions

Steps for using pump saver to protect the unit during storage.

Troubleshooting

Unit will not turn on.

Corrective actions for when the pressure washer fails to power on.

No water flow.

Troubleshooting steps for when the unit runs but no water is dispensed.

Hose connection leaks.

Solutions for leaks at the high pressure hose connection point.

Unit cycles on;off.

Diagnosing and resolving issues where the unit turns on briefly and shuts off.

Warranty Process

MasterForce MFX2U2200 Specifications

General

Maximum Pressure (PSI)	2200
Flow Rate (GPM)	1.2
Power Source	Electric
Voltage	120V
Pump Type	Axial Cam

Related product manuals

Preview: MasterForce MF3N12300

MasterForce MF3N12300

Preview: MasterForce 261-1680

MasterForce 261-1680

MasterForce 5100094VT