What to do if the incline is short circuited on Matrix Fitness Equipment?
If the incline is short-circuited or has overcurrent on your Matrix fitness equipment, check for misalignment of the incline motor and replace if needed.
What to do if incline calibration is over 80 seconds on Matrix A3X-02 Fitness Equipment?
If the incline calibration takes over 80 seconds or doesn't complete on your Matrix fitness equipment, replace the LCB or Incline Motor.
What to do if the display is stuck on heart rate on Matrix A3X-02?
If your Matrix fitness equipment display is stuck on heart rate, this is often due to the lighting conditions in your workout area. Try adjusting the lighting in the immediate vicinity of the equipment or move the equipment to a different location within the facility. Also, ensure that no one nearby is using a telemetric heart rate strap or watch.
What to do if the incline has no action for 5 seconds on Matrix A3X-02?
If the UCB implements an incline command, and the incline on your Matrix fitness equipment doesn't respond for 5 seconds, replace the Incline Motor or LCB.
What to do if the LCB battery voltage is low on Matrix Fitness Equipment?
If the LCB battery voltage is low (below 11.2V) on your Matrix fitness equipment, plug in the machine for AC charge and temporarily avoid using the incline function.
Why does the incline stop on self-powered Matrix A3X-02 when the LCB battery is low?
If your self-powered Matrix fitness equipment's incline stops because the LCB battery capacity is too low or the RPMs aren't high enough (below 70 RPM), replace the LCB.
What to do if the LCB is not receiving a command from the UCB on Matrix A3X-02 Fitness Equipment?
If the UCB implements a command and the LCB is not receiving it on your Matrix fitness equipment, check the console cable connections. If needed, update the LCB software, or replace the LCB or UCB.
How to fix the incline motor that has no action or current on Matrix A3X-02 Fitness Equipment?
If the incline motor on your Matrix fitness equipment has no action or current, replace the incline motor.
What to do if LCB LEDs are lit, but there is no power to the console on Matrix Fitness Equipment?
If the LCB LEDs are lit but there's no power to the console on your Matrix fitness equipment, check if LED 1 is lit on the upper control board. If it's not, check the console cable connection at both the LCB and the console. If LED 1 remains unlit after checking the connections, use a multimeter to check pins 1 and 3 on the console cable for approximately 12V. If necessary, replace the console cable. If LED 1 is lit on the console but there's still no power, replace the console.
What to do if the LCB is not getting power from the power receptacle on Matrix A3X-02 Fitness Equipment?
If the LCB on your Matrix fitness equipment isn't receiving power from the power receptacle, check if LED 15 is lit on the LCB. If it's not, check for incoming AC voltage at the LCB. If there's no voltage, replace the power components as needed. If all power components are functioning and AC voltage is present at the LCB, replace the LCB.
General| Brand | Matrix |
|---|---|
| Model | A3X-02 |
| Category | Fitness Equipment |
| Language | English |
Locates the serial number on the Ascent Trainer.
Provides essential safety guidelines for operating the Ascent Trainer.
Details the electrical specifications and grounding requirements for the Ascent Trainer.
How to enter and navigate the Manager Mode for customization.
Details various customizable settings available in Manager Mode.
Instructions to access and utilize the Engineering Mode for advanced settings.
Guide to entering and navigating the Service Mode for diagnostics and tests.
Visual representation of the Ascent Trainer's electrical components and connections.
Lists console error codes, their descriptions, and recommended solutions.
Troubleshooting steps for error codes 0140 and 01B2 related to incline motor issues.
Troubleshooting steps for error code 01A0 concerning a disconnected incline motor.
Steps to diagnose and resolve issues where the console has no power.
Guidance on diagnosing and fixing problems with heart rate display or readings.
Troubleshooting RPM issues and failure to record distance.
Detailed steps for removing and installing the incline motor.
Step-by-step guide for updating the Ascent Trainer's console software.
To Next Page
