Maytag CS User Manual

PLACING DRYER IN OPERATION
After the dryer has been properly installed, there are a few steps required before the dryer is ready
for operation.
CS & PS MODELS
(COIN OPERATED)
CS/PS models are activated by a coin slide.
Install the coin slide (not provided with product)
as follows:
First, remove the coin slide actuator from
accessory package that is found in the
coin box.
Two (2) screws from the package attach
the actuator bracket to the coin slide.
PS MODELS ONLY refer to PD set-up instruc-
tions for selecting coin slide option "ON", and
for other set-up options.
DISCONNECT ELECTRICAL SUPPLY.
1. Remove the service door from control
center.
ACCUMULATIVE
More Than One Coin Slide Actuation -
To accumulate, this mechanism can be set
up for one, two or three actuations of the
slide. The maximum amount of time which
can be accumulated is 60 minutes. This
must be done at the start of the cycle to
insure the correct time has been
accumulated.
HOW IT WORKS
When the slide is pushed in, the coin slide will
move the actuator arm inward, pivoting the
switch actuator. This in turn moves the switch
actuator arm towards the timer shaft.
SLIDE
CONTACTS
HERE
.
Using a driver, unscrew the bolt (located in
control center) from retainer in from face of
the control center.
3. Install the actuator bracket to the coin slide.
4. Insert the coin slide into the control center
and thread retaining bolt into slide housing.
ACTUATOR
ARM
SWITCH
ACTIVATOR
ARM
SWITCH
ACTUATOR
As the slide continues to be pushed inward it
will contact the index wheel driver releasing the
index wheel. The index wheel return spring will
rotate the index wheel in a counterclockwise
direction. It will continue rotating until the
switch actuator arm catches a movable return
stop. This stops the rotation of the index wheel
for the first slide actuation.
INDEX
NOTE:
Some coin slides may require
breaking and removing the tab on
the actuator bracket.
INDEX
WHEEL
DRIVE
/
k
|
r ACTUATOR ROD
SWITCH BRACKET IS ADJUSTABLE
TO ACCOMMODATE ANY COIN SLIDE.
5. On PS models, make certain short leg of
ACTUATOR ROD is inserted through slot in
the actuator bracket.
6. Reinstall service access door.
TIME ADJUSTMENT
INSTRUCTIONS -
CS ONLY
This timing mechanism can be either
accumulative or nonaccumulative. When
shipped, the dryer will be set up for
nonaccumulative operation with the time adjust-
ment peg in position "C".
NONACCUMULATIVE
One Coin Slide Actuation -
Refer to charts for information on various
times available and set-up instructions.
MOVABLE
RETURN
STOP
During the second coin slide actuation, the
switch actuator will move into position and the
index wheel will continue rotating as described
in the previous actuation. It will continue
rotating until either the switch actuator arm
catches a second movable stop or the index
wheel timing lug contacts the timer bracket tab.
TIMER
BRACKET
TAB
INDEX
WHEEL
TIMING
LUG
When a second movable stop is used, a third
actuation of the side is possible. The third
actuation will allow rotation of the index wheel
counterclockwise until the index wheel timing
lug contacts the timer bracket tab. Once the
timing lug contacts the bracket tab, no
additional drying time can be obtained.

Maytag CS Specifications

General

Brand	Maytag
Model	CS
Category	Dryer
Language	English

Summary

CS & PS MODELS (COIN OPERATED)

ACCUMULATIVE OPERATION

Explains how to accumulate multiple coin actuations for extended drying time.

HOW IT WORKS

Details the mechanical process of coin slide actuation affecting timer mechanisms.

TIME ADJUSTMENT INSTRUCTIONS

Instructions for setting the dryer's timer for accumulative or nonaccumulative operation.

NONACCUMULATIVE OPERATION

Describes single coin actuation for nonaccumulative drying time settings.

COMMERCIAL DRYER OPERATING INSTRUCTIONS

SET-UP INSTRUCTIONS (CS ONLY)

Step-by-step guide for setting up the coin slide mechanism for CS models.

TIMER SETTING OPTIONS

NON-ACCUMULATIVE TIMER SETTINGS

Options for setting non-accumulative drying times based on coin slide actuations.

ACCUMULATIVE TIMER SETTINGS

Options for setting accumulative drying times using multiple coin slide actuations.

LOCKS AND KEYS

INSTALLING COIN BOX LOCK

Procedure for installing the coin box lock mechanism and spring washer.

MN MODELS (MANUAL NON-COIN)

OPERATION

Instructions for operating manual non-coin dryer models.

PD, PR, PN & PS MODELS (COMPUTER MODELS)

TO OPERATE DRYER

General steps for operating computer-controlled dryer models using coins or debit cards.

GENERAL USER INFORMATION

Information on display states, cold start, warm start, and operational notes.

PRICING OPTIONS

Details on fixed vend, accumulator, and top-off pricing for dryer cycles.

CONTROL SET-UP PROCEDURE

Guide to using key pads and digital display for programming dryer controls.

CONTROL SET-UP (continued)

SET-UP CODES: REGULAR CYCLE PRICE

Code for setting the base price per cycle or number of coins for operation.

SET-UP CODES: VALUE OF COIN 1

Defines the value of the first coin or debit input in nickels for pricing.

SET-UP CODES: VALUE OF COIN 2

Defines the value of the second coin or debit input in nickels for pricing.

SET-UP CODES: SPECIAL PRICING OPTIONS

Enables special pricing features and access to related set-up codes.

DIAGNOSTIC CODES

SINGLE DRYERS DIAGNOSTIC CODES

Error codes for single dryer control board and component failures.

STACKED DRYERS DIAGNOSTIC CODES

Error codes for stacked dryer control board and component failures.

DRYER DIAGNOSTIC MODE

SINGLE LOAD MODELS DIAGNOSTIC CYCLE

Procedure to run a diagnostic test cycle on single load dryer models.

STACKED MODELS DIAGNOSTIC CYCLE

Procedure to run a diagnostic test cycle on stacked dryer models.

DRYER HELP MODE