To Next PageTo Next Page
Need help?Do you have a question about the Maytag MEDB725BW0 and is the answer not in the manual?
General| Brand | Maytag |
|---|---|
| Model Number | MEDB725BW0 |
| Product Type | Dryer |
| Fuel Type | Electric |
| Capacity | 7.0 cu. ft. |
| Color | White |
| Control Type | Electronic |
| Number of Options | 5 |
| Wrinkle Care Option | Yes |
| Moisture Sensor | Yes |
| Voltage | 240 V |
| Amperage | 30 A |
| Power Cord | Not included |
| Door Reversal | Yes |
| Energy Star Certified | No |
| Width | 27 in |
| Height | 43 in |
| Warranty | 1 Year |
Explains safety alert symbols, DANGER, and WARNING terms.
Installation must be by qualified installer; avoid plastic/foil vents to prevent fire.
Legal warnings regarding chemicals known to cause cancer or reproductive harm.
Details required tools and all supplied parts for installation.
Specifies minimum space requirements for dryer installation and door operation.
Provides detailed measurements and diagrams for dryer models.
Specific provisions for mobile homes, including venting and standards.
Contact qualified electrician; ensure adherence to codes and standards.
Details 3-wire vs 4-wire connections and cabinet grounding.
Specifies UL listed cord and strain relief for power supply cord.
Guides selection of 4-wire or 3-wire power cords based on outlet.
Explains proper grounding for cord-connected and permanently connected dryers.
Warns about the weight and need for multiple people.
Instructs on protecting the floor and positioning the dryer.
Details how to install and adjust the leveling legs.
Warnings about fire hazard and requirements for power supply cords.
Lists choices for power supply cord or direct wire connections.
Steps for attaching the strain relief to the power supply cord.
Removing screws and preparing wires for connection.
Instructions for connecting neutral wires to the terminal block.
Instructions for connecting the ground wire to the terminal block.
Final steps for connecting the remaining wires.
Step to remove the center screw before connecting wires.
Instructions for connecting the neutral wire.
Final steps to connect remaining wires and secure cover.
Step to attach the strain relief for direct wire connection.
Instructions for preparing the 4-wire cable for connection.
Steps to attach the direct wire cable to the strain relief.
Instructions for preparing the 3-wire cable for connection.
Step to remove the center screw for connection.
Steps to connect the remaining wires for 3-wire direct connection.
Requirement to verify grounding method with an electrician.
Steps to prepare for connecting neutral ground and neutral wires.
Fire hazard warnings and prohibition of plastic/foil vents.
Dryer must be exhausted outdoors, avoiding specific building areas.
Details requirements for heavy metal, rigid, and flexible metal vents.
Notes on cleaning lint and replacing old vent types.
Shows typical rear and optional exhaust configurations.
Recommends hood styles, elbow types, and clamp usage.
Lists potential issues like moisture damage and health problems.
Describes over-the-top and periscope installations for tight spaces.
Guidelines for choosing the best route, minimizing elbows and kinks.
Instructs on using the chart to determine vent material and length for optimal performance.
Instructions to turn off water and prepare hoses and faucet.
Steps for connecting the short hose and "Y" connector to the faucet.
Instructions on how to properly tighten hose couplings.
Attaching the long hose to the "Y" connector and tightening.
Attaching the long hose to the dryer's fill valve and tightening.
Turning on the faucet and checking for any leaks.
Instructions for connecting the dryer vent to the exhaust outlet.
How to check if the dryer is level using a level.
Instructions for adjusting the legs to achieve a level dryer.
Checklist of items to confirm before operation.
Steps to remove the dryer door and hinges.
Instructions for removing and reinstalling the door strike and screws.
Steps for removing, reinstalling, and aligning door hinges and screws.
