Maytronics Dolphin M600

Questions and Answers

M
Mrs. Katie GarrettSep 8, 2025
How to fix a Maytronics Vacuum Cleaner that is moving in circles?
- E
  Edward JohnsonSep 9, 2025
  If your Maytronics Robotic Pool Cleaner is moving in circles, consider the following: * The filter basket may be clogged, so clean it. * There might be debris stuck in the impeller house or impeller cover; if so, remove it. * The power supply could be incorrectly positioned. Place it in a location that allows the cleaner to reach the entire pool area freely. * Algae buildup or pool water that doesn't meet specifications can also cause this. Correct the pool and water conditions.
R
robertyoungAug 23, 2025
Why is my Maytronics Swimming Pool Vacuum not moving?
- J
  Joseph MasonAug 23, 2025
  If your Maytronics Swimming Pool Vacuum isn't moving, first check that the floating cable is securely connected to the power supply. If it is, unplug the power supply and inspect the impeller cover to ensure nothing is trapped in the impeller. Also, check the tracks and wheels for any obstructions.
J
Jamie AndersonAug 25, 2025
Why does my Maytronics Swimming Pool Vacuum move in circles?
- L
  laceymillerAug 25, 2025
  If your Maytronics Swimming Pool Vacuum is moving in circles, start by cleaning the filter basket. Debris stuck in the impeller house or impeller cover could also be the cause; remove any obstructions you find. Ensure the power supply is positioned correctly, allowing the Robotic Pool Cleaner to freely reach the entire pool area. Algae buildup or unsuitable pool water conditions can also cause this issue, so ensure that you correct the pool and water conditions.
D
Daniel StephensonAug 26, 2025
What to do if my Maytronics Swimming Pool Vacuum doesn't climb the walls?
- M
  michaelrichardsAug 27, 2025
  If your Maytronics Swimming Pool Vacuum isn’t climbing walls, the filter basket may be clogged, so try cleaning it. Algae on the walls can also prevent climbing; check the chemical levels in the water and adjust them if necessary, then scrub the walls. An unsuitable pH level can also cause this, so check the level of chemicals in the water. Also, check for and remove any debris stuck in the impeller house or impeller cover.
J
James ClayAug 27, 2025
What to do if my Maytronics Swimming Pool Vacuum is not cleaning the pool even though it moves?
- T
  Travis StevensAug 27, 2025
  If your Maytronics Swimming Pool Vacuum moves but doesn't clean, the filter basket might be clogged; try cleaning it. Also, check for any debris stuck in the impeller house or impeller cover and remove it.
S
Scott SkinnerSep 22, 2025
How to fix Wi-Fi connection issues with my Maytronics Vacuum Cleaner?
- H
  haleymcdonaldSep 22, 2025
  If you cannot connect to your Maytronics Vacuum Cleaner's Wi-Fi®, and the communication LED is blinking green, here are some troubleshooting steps: * Reset the power supply by disconnecting the power cord and waiting 1 minute. * Check that your smartphone has strong Wi-Fi® connectivity near the power supply by trying to play an online video. * Verify that your home router is working properly. * Position the power supply as close as possible to the home router. * Install a Wi-Fi® extender (2.4Ghz) to ensure sufficient signal strength.
M
Madeline SimpsonSep 16, 2025
What causes a Maytronics Vacuum Cleaner to move in one direction only?
- D
  Dan LeachSep 16, 2025
  If your Maytronics Robotic Pool Cleaner does not turn or moves in one direction only, the problem may be that debris is stuck in the impeller house or impeller cover. Remove any debris stuck in these areas.
M
mhaasSep 18, 2025
What to do if I can't connect to my Maytronics Vacuum Cleaner via Bluetooth®?
- S
  Sarah HayesSep 18, 2025
  If you can't connect to your Maytronics robot via Bluetooth®, and the communication LED is blinking blue, it could be due to: * The power supply being too far from the smart device, Bluetooth® being disabled, or Bluetooth® not working properly. Try turning Bluetooth® off and then on in your smartphone settings. * Try getting closer to the IoT power supply. * Make sure there aren't any interferences or obstacles. * Turn the power supply off and then on.
T
Tammy CampbellSep 7, 2025
Why is my Maytronics Vacuum Cleaner not cleaning the pool?
- J
  Jennifer ProctorSep 7, 2025
  If your Maytronics Robotic Pool Cleaner moves but does not clean the pool, the issue may be due to: * A clogged filter basket. Clean the filter basket. * Debris stuck in the impeller house or impeller cover. Remove any debris from these areas.
M
Mary CaseySep 4, 2025
What to do if I can not connect to my Wi-Fi®, and the communication Led is blinking Green on my Maytronics Swimming Pool Vacuum?
- S
  Susan SextonSep 4, 2025
  If you cannot connect to your Wi-Fi® and the communication LED is blinking green on your Maytronics Swimming Pool Vacuum, reset the power supply (disconnect the power cord) and wait 1 minute. Check that your smartphone has strong Wi-Fi® connectivity near the power supply. Verify that the home router is working properly. Locate the power supply as close as possible to the home router. You may need to install a Wi-Fi® extender (2.4Ghz) to ensure sufficient signal strength.

Summary

Introduction

Specifications

Warnings and Cautions

Water Conditions

Specifies the recommended chlorine, pH, temperature, and NaCl levels for optimal cleaner performance.

Setting Up Wi-Fi

Guides on connecting the robotic pool cleaner to your home Wi-Fi network for app control.

Robotic Pool Cleaner Parts

Using the Robotic Pool Cleaner

Setup Procedure

Step-by-step instructions for initial setup before the first use of the pool cleaner.

Placing into the Pool

Instructions on how to properly place the robotic pool cleaner into the swimming pool.

Connecting to Smart Device

Guide to connecting the robotic pool cleaner to a smart device via the MyDolphin App.

Operating Without Smart Device

How to operate the robotic pool cleaner using its onboard controls without a smart device.

Power Supply and Indicators

Details on the power supply unit, its operation, and interpretation of LED indicator lights.

Removing from Pool

Safe procedures for turning off, unplugging, and removing the robotic pool cleaner from the pool.

Care and Maintenance

Cleaning Dual Filter Basket

Instructions for removing and cleaning the dual filter basket after each use.

Periodic Filter Cleaning

Recommended monthly procedure for thorough cleaning of the filter panels.

Cleaning the Impeller

Steps to clean debris trapped in the impeller opening.

Weekly General Maintenance

Recommended weekly tasks for general maintenance and cable care.

Off-Season Storage

Troubleshooting

Power Supply Issues

Resolving problems where the power supply or its LEDs are not working.

Cleaner Not Moving

Troubleshooting steps when the robotic pool cleaner fails to move.

Cleaner Moving in Circles

Addressing issues causing the cleaner to move in circles.

Directional Movement Issues

Solutions for the cleaner not turning or moving in only one direction.

Cleaning Performance Issues

Fixing problems where the cleaner moves but does not clean the pool effectively.

Incomplete Pool Coverage

Troubleshooting why the cleaner only covers part of the pool.

Floating Cable Kinks

Resolving issues related to kinks in the floating cable.

Wall Climbing Problems

Steps to take when the robotic pool cleaner does not climb the walls.

Wi-Fi Connectivity

Troubleshooting connection problems with the Wi-Fi network.

Bluetooth Connectivity

Resolving issues when unable to connect to the robot via Bluetooth.