Mazda 0000-8L-R02 - User Manual

INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACIÓN
INSTRUCTIONS D’INSTALLATION
1
A) Read entire installation instruction sheet before proceeding.
Lea toda la hoja de las instrucciones de instalación antes de proceder
Lire toutes les instructions avant de procéder à l’installation.
B) Wear eye protection.
Use protección visual.
Porter des lunettes de protection.
C) Note orientation arrows to assure proper installation.
Preste atención a las flechas de orientación para garantizar una instalación correcta.
Noter l’orientation des flèches pour bien installer.
Note: Maximum Load - 165 Lbs Evenly Distributed
Carga Máxima - 165 lbs Distribuidas Uniformemente
Charge Maximum - 165 lbs Également Distribuées
PACKAGE CONTENTS
Contenido del paquete
Contenu de l’emballage
Front of vehicle arrows
Flecha indicadora de frente del vehiculo
Flèche indiquant l’avant du véhicule
Break off the rear (longer) tabs before installing
Separe las lengüetas traseras (más largas) antes de instalar
Cassez les taquets arrière (plus longs) avant d’installer
Front of Vehicle
Frente del vehiculo
Avant du véhicule
Front of Vehicle
Frente del vehiculo
Avant du véhicule
Front of Vehicle
Frente del vehiculo
Avant du véhicule
Front Cross Bar
la barra transversal delantera
cruzada frente a bar
Rear Cross Bar
Barra transversal trasera
Traverse arrière a bar
CROSS BARS
BARRAS TRANSVERSALES
CROISILLONS
Genuine Accessories
Accesorios Genuinos
Accessoires D’origine
0000-8L-R02
Part Number:
Número De Parte:
Numéro De Pièce:
Applicable Models:
Modelos Aplicables:
Modèles Concernés:
2013 > CX-5
TOOLS REQUIRED
Herramientas necesarias
Outils requis
Before Installation
Antes de la instalación
Avant l’installation
0
Install Sliders
Instale los deslizadores
Installez les supports coulissants
2
Remove Rear Covers
Retire las cubiertas traseras
Enlevez les couvercles arrière
Flat Head Screwdriver
Destornillador de cabeza plana
Tournevis à tête plate
Tie Down Loops (Qty. 4)
Fijaciones (Cant. 4)
Boucles d’arrimage (qté 4)
Slider Mounts (2 LH, 2 RH)
Soportes deslizables (2 lado derecho, 2 lado izquierdo)
Supports coulissants (2 dt 2 gch)
(LH SHOWN RH TYPICAL)
(Lado izquierdo mostrado Lado derecho típico)
(Gche indiquée, dte semblable)
3
Install Cross Bars
Instale las barras transversales
Installez les croisillons
(LH SHOWN RH TYPICAL)
(Lado izquierdo mostrado Lado derecho típico)
(Gche indiquée, dte semblable)
2
1
51507B 20111205

Summary

Preparation and Initial Steps

Read Instructions and Safety Precautions

Review all instructions and wear eye protection before installation.

Note Orientation Arrows

Follow directional arrows for correct part placement and installation.

Remove Rear Covers

Remove the covers from the rear vehicle rails to begin installation.

Install Main Components

Prepare Sliders

Break off the rear (longer) tabs on the slider mounts before installation.

Install Sliders

Mount the slider supports onto the vehicle rails.

Install Cross Bars

Attach the cross bars to the vehicle after sliders are installed.

Install Tie-Down Loops

Rotate Tie-Down Loops

Rotate tie-down loops clockwise until tight, ensuring an audible click.

Cross Bar Removal and Storage

Cross Bar Storage

Position cross bars in the 'NOT IN USE POSITION' when not mounted.

Cross Bar Removal Steps

Follow sequential steps to safely remove cross bars and related components.

Discard Side Rail Instructions

Replace original side rail instructions with these cross bar instructions.

Mazda 0000-8L-R02 Specifications

General

Brand	Mazda
Model	0000-8L-R02
Category	Automobile Accessories
Language	English