Mazda KMV6V7210 User Manual

MAZDA NORTH AMERICAN OPERATIONS
550-0775 Rev. AAA
*550-0775-000*
Thank you for purchasing a Genuine Mazda Accessory.
Before removal and installation, Please thoroughly read these instructions.
For your safety, please read the contents of this booklet to properly install and use the Digital
Rearview Mirror. Keep these instructions with your vehicle records for future reference.
· There are several WARNINGand CAUTIONsections in this booklet concerning safety when
installing or removing the Digital Rearview Mirror . Always read and follow the instructions in order to prevent
injuries, accidents, and possible damage to the vehicle.
!
WARNING: Indicates a situation in which serious injury or death could result if the warning
is ignored.
!
CAUTION: Indicates a situation in which bodily injury or damage to the vehicle could
result if the caution is ignored.
· For areas indicating the tightening torque in this instruction manual, tighten to the specified torque by
using a torque wrench. For areas in which the tightening torque is indicated inside parentheses ( ), the
tightening torque is indicated as a reference value, however tightening using a torque wrench is not
necessary.
· Do not modify the Digital Rearview Mirror or kit components.
· Do not install the Digital Rearview Mirror in any way other than described in the following instructions.
· If in doubt, please contact your Mazda dealer to install the accessory in order to prevent errors in installation.
· If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before
using it.
· Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property
that arise from the failure of the dealer or installer to follow these instructions.
· To ensure safety and reliability of the work, installation, removal and disposal work must be carried out by an
Authorized Mazda Dealership.
· Be careful not to lose removed parts, and be sure that they are kept free of dirt, scratches, or damage.
PART NAME Digital Rearview Mirror
PART NUMBER KMV6V7210/KMS6V7210
VEHICLE MAZDA CX90
!
GENUINE DIGITAL REARVIEW MIRRORGENUINE DIGITAL REARVIEW MIRROR
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
WARNING
!
!

Mazda KMV6V7210 Specifications

General

Brand	Mazda
Model	KMV6V7210
Category	Automobile Accessories
Language	English

Summary

1. Parts

2. Installation View

3. Before Installation

Required Tools

Lists necessary tools for installation.

Other Preparations

Lists additional items needed for safe installation.

4. Connector Diagram

5. Vehicle Part Removal

Negative Battery Terminal Disconnection

Instructions for safely disconnecting the battery.

Sensor Cover Removal

Steps to remove the sensor covers.

Rear View Mirror Removal

Procedures for removing the rearview mirror.

Indicator Sensor Removal

Steps to remove the indicator sensor.

Front Door Sill & Weather Seal Removal

Instructions for removing front door sill and weather seal.

Rear Door Sill & Weather Seal Removal

Instructions for removing rear door sill and weather seal.

A-Pillar Trim Removal

Steps to remove the A-pillar trim.

Lower Dash Removal

Instructions for removing lower dash trim.

Hood Release Lever Removal

Steps to remove the hood release lever.

Driver-Side Air Vent Removal

Instructions for removing the driver-side air vent.

Driver-Side Lower Panel Removal

Steps to remove the driver-side lower panel.

Trunk Trim Removal

Instructions for removing trunk trim.

D-Pillar Trim Removal

Steps to remove the D-pillar trim.

Disengaging Headliner

Instructions for disengaging the headliner clips.

6. Mirror Installation

Place Camera

Steps to prepare and mount the camera.

Routing Coax Cable Through Rear Liftgate

Routing the coax cable through the rear liftgate.

Connect Coax Cable to Camera

Connecting the coax cable to the camera.

Routing Coax Cable

Routing the coax cable through the vehicle interior.

Accessory Mirror Power Harness Installation

Installing the accessory mirror power harness.

Install Full Display Mirror

Steps to mount the full display mirror.

Attach Harness Clip and Connectors

Attaching harness clips and connectors to the mirror.

7. Verification

Mirror Function Confirmation

Confirming the display and camera functions correctly.

8. Camera Cover Placement

Installing Camera Cover

Steps to install the camera cover.

9. Vehicle Part Reassembly

Vehicle Reassembly

Steps for reassembling vehicle parts after installation.

Inspection

Checklist for inspecting installed components and fit.