120 McQuay IM 987
Rooftop Equipment Warranty Regist. Form
Warranty Registration Form (continued)
VI. GAS & OIL BURNER CHECK, TEST, & START
Specifications:
For gas, see Forced Draft Gas Burner Installation and Maintenance Bulletin.
For oil, see Oil Fired Furnace Installation and Maintenance Bulletin.
A. (Gas/Oil) Furnace model no. __________________
B. (Gas/Oil) Burner model no. __________________ Serial no. ___________________
C. (Gas) Type firing: Single Stage two Stage modulation
D. (Oil) Type firing start: Full fire start Low fire start
E. (Gas) Rated firing rate:_________________ MBH input
F. (Oil) Rated firing rate: _________________ GPH, #2 fuel oil
G. (Gas/Oil) Altitude: ___________________ ft. above sea level
H. Is there a circulating tank? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes No N/A
VII. GAS BURNER CHECK, TEST, & START
A. Input: _______________________________ CFH
B. Gas pressure at burner: _________________ inches wc
C. CO
2
: __________________________ %
D. CO
2
: __________________________ %
E. Pilot flame only: _______________microamps (steady at low fire)
F. Pilot Tap-gas pressure:__________________ inches wc
G. Motor only/burner: FLA__________________ running amps
H. High limit control OK?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes No N/A
I. Flame safeguard: ________________ microamps
J. Flame failure shutoff: ________________ seconds
K. Airswitch OK?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes No N/A
L. High Gas Pressure Switch OK? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes No N/A
M. Low Gas Pressure Switch OK? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes No N/A
N. Main Gas Valve Close-off OK?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes No N/A
VIII. OIL BURNER CHECK, TEST & START
A. Nozzle(s): Type/manufacturer GPH Angle Pattern manufacturer
B. Nozzle pressure: _______________________ psi
C. CO
2
: __________________________ %
D. Smoke spot: number ______________
E. Running amps ________________ FLA
F. Flame safeguard: microamps_________________
G. High limit control OK?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes No N/A
H. Flame failure shutoff OK?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes No N/A
I. Ignition failure check OK? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes No N/A
IX. Have all electronic or electrical controls been checked, adjusted, and tested for proper operation per the
installation and maintenance bulletins?
Yes No N/A
X. MAINTAINING MICROTECH CONTROL PARAMETER RECORDS
After the unit is checked, tested, and started and the final control parameters are set, record the final settings. Keep these records on file and
update whenever changes to the control parameters are made. Keeping a record facilitates any required analysis and troubleshooting of the
system operation and facilitates restoration after a controller replacement.
Signature: ______________________________________________________ Startup date: ___________________________________
RETURN COMPLETED FORM TO:
McQuay International Warranty Department, 13600 Industrial Park Boulevard, Minneapolis, MN 55441
Please list any additional comments that could affect the operation of this unit; e.g., shipping damage, failed components, adverse installation
applications, etc., on a separate sheet and attach to this form.