How to order your complete Multi-point Lubrication System
1. MEMO Setting
Lubricant output is determined by preprogramming the
“MEMO” fitting. Please refer to the “MEMOLUB®HPS
Lubricator Installation Instructions for proper output settings.
2. Lubricant required.
Additional Ordering Information Required:
The part # MPS - P4 - R - 04 - G- 02 will be a Grease system
with a 4 point distribution block, a Mega MEMOLUB®HPS
Lubricator (Model 240 HPS) with straight bearing fittings
having a 1/4” NPT Male thread.
Example:
MEMOLUB® MPS Systems Ordering Information
MPS4PGIN-0103-PG2 Copyright © 2003 PLI, LLC All Rights Reserved
Bearing Fittings
MPS - PX - X - XX - X - XXX
R = Regular Configuration
Self-contained battery powered lubricator.
C = EPC (External Power Control)
Self contained battery powered lubricator
with external “On-Off” control.
S = EPS (External Power Source)
Lubricator powered with an external power
source (no battery pack).
Power Options
Type of Distribution Block
O = Oil
G = Grease
02 = 2 outlet ports (2 outlets @ .6 cc’s)
03 = 3 outlet ports (3 outlets @ .6 cc’s)
04 = 4 outlet ports (4 outlets @ .3 cc’s)
05 = 5 outlet ports (4 outlets @ .3 cc’s, 1 outlet @ .6 cc’s)
06 = 6 outlet ports (6 outlets @ .3 cc’s)
07 = 7 outlet ports (6 outlets @ .3 cc’s, 1 outlet @ .6 cc’s)
08 = 8 outlet ports (8 outlets @ .3 cc’s)
09 = 9 outlet ports (6 outlets @ .3 cc’s, 3 outlets @ .6 cc’s)
10 = 10 outlet ports (8 outlets @ .3 cc’s, 2 outlets @ .6 cc’s)
11 = 11 outlet ports (10 outlets @ .3 cc’s, 1 outlet @ .6 cc’s)
12 = 12 outlet ports (12 outlets @ .3 cc’s)
Number of outlet ports
Lubricator size
P3 = Standard HPS Model 120 (120cc of lubricant)
P4 = Mega HPS Model 240 (240cc of lubricant)
P5 = Giga HPS Model 480 (480cc of lubricant)
5/16” (8mm) OD Nylon Tubing Fittings
(These systems use IF3109-08-10 Block Fittings)
1/4” OD Nylon Tubing Fittings
(These systems use IF3109-56-10 Block Fittings)
51 = Straight 1/8” NPTM - (IF3175-56-11)
52 = Straight 1/4” NPTM - (IF3175-56-14)
53 = 90° - 1/8” NPTM - (IF3109-56-11)
54 = 90° - 1/4” NPTM - (IF3109-56-14)
Stainless Steel Push-In Fittings
SS1 = Straight 1/8” NPTM - (IF3805-08-11)
SS2 = Straight 1/4” NPTM - (IF3805-08-14)
SS3 = 90° - 1/8” NPTM - (IF3889-08-11)
SS4 = 90° - 1/4” NPTM - (IF3889-08-14)
5/16” (8mm) OD Copper Tubing
Compression Fittings
(These systems use IF3175-08-10CCP Block Fittings)
CC1 = Straight 1/8” NPTM - (IF3175-08-11CCP)
CC2 = Straight 1/4” NPTM - (IF3175-08-14CCP)
CC3 = 90° - 1/8” NPTM - (IF3109-08-11CCP)
CC4 = 90° - 1/4” NPTM - (IF3109-08-14CCP)
1/4” OD Copper Tubing
Compression Fittings
(These systems use IF3175-56-10CCP Block Fittings)
CC6 = Straight 1/8” NPTM - (IF3175-56-11CCP)
CC7 = Straight 1/4” NPTM - (IF3175-56-14CCP)
CC8 = 90° - 1/8” NPTM - (IF3109-56-11CCP)
CC9 = 90° - 1/4” NPTM - (IF3109-56-14CCP)
5/16” (8mm) OD Steel Tubing
Compression Fittings
(These systems use IF3175-08-10SCP Block Fittings)
SC1 = Straight 1/8” NPTM - (IF3175-08-11SCP)
SC2 = Straight 1/4” NPTM - (IF3175-08-14SCP)
SC3 = 90° - 1/8” NPTM - (IF3109-08-11SCP)
SC4 = 90° - 1/4” NPTM - (IF3109-08-14SCP)
Plastic Push-In Fittings
01 = Straight 1/8” NPTM - (IF3175-08-11)
02 = Straight 1/4” NPTM - (IF3175-08-14)
03 = 90° - 1/8” NPTM - (IF3109-08-11)
04 = 90° - 1/4” NPTM - (IF3109-08-14)
Refer to Set-up Guide for details
A complete MEMOLUB® MPS (Multi-Point System) can be ordered by using the quick coding below.
Simply replace the “X’s” with the code corresponding to your selection in the sub-menus. Additional
installation parts and nylon tubing (empty or pre-filled with lubricant) are also available.
MEMOLUB® HPS User's Guide Page 26 of 39 PLI, LLC
To Next Page
Loading...
