To Next Page
M
morrisangelaAug 19, 2025
Why is the red LED flashing rapidly on my Menuett 008164 Vacuum Cleaner?
- TTerrance CrawfordAug 19, 2025
The red LED flashes rapidly because the battery voltage is too low. To resolve this, charge the vacuum cleaner.
Why is the red LED flashing rapidly on my Menuett 008164 Vacuum Cleaner?
The red LED flashes rapidly because the battery voltage is too low. To resolve this, charge the vacuum cleaner.
Why does my Menuett 008164 suddenly stop and the blue LED stays on?
The vacuum cleaner may stop suddenly with a constant blue LED because it's hanging on an edge, the step sensor detects a fall risk, or one of the wheels isn't touching the floor. Put the vacuum cleaner back on the floor and restart it.
What to do if my Menuett 008164 Vacuum Cleaner doesn't change direction when hitting an obstacle?
If the vacuum cleaner doesn't change direction when it meets an obstacle, it could be a fault with the bumper sensor. Check the sensitivity of the bumper sensor and make sure no foreign object is stuck to it.
What to do if the red LED flashes rapidly and there's an audio prompt while charging my Menuett 008164 Vacuum Cleaner?
If the red LED flashes rapidly and there is an audio prompt during charging, the power switch on the vacuum cleaner might not be in the ON position. Press the power switch to resolve this.
What does it mean when the blue LED flashes once and the red LED flashes three times on my Menuett Vacuum Cleaner?
If the blue LED flashes once and the red LED flashes three times, it indicates that the wheels are blocked. Remove the blockage.
What does it mean when the blue LED and red LED flash once on my Menuett 008164 Vacuum Cleaner?
If the blue LED flashes once and the red LED flashes once, the side brush on the vacuum cleaner has become entangled or stuck. Move the vacuum cleaner and untangle the brush.
What does it mean when the blue LED flashes once and the red LED flashes twice on my Menuett 008164?
If the blue LED flashes once and the red LED flashes twice, the bumper on the main unit is not flexible. Undo the bottom screws on the bumper.
What to do if my Menuett 008164 Vacuum Cleaner stops when in use and the blue LED is constant?
If your Menuett Vacuum Cleaner stops while in use and the blue LED is constant, it could be stuck on an edge, with the step sensor detecting a fall risk. To fix this, put the product on the floor and start it again.
What to do if my Menuett 008164 Vacuum Cleaner does not change direction when it touches an obstacle?
If your Menuett Vacuum Cleaner isn't changing direction upon hitting an obstacle, the bumper sensor might be blocked or defective. Check the bumper sensor and remove any foreign objects. Speak to an authorized service center if the bumber sensor is defective.
What to do if the blue LED flashes 1 time, and the red LED flashes 3 times on my Menuett Vacuum Cleaner?
If the blue LED flashes once and the red LED flashes three times on your Menuett Vacuum Cleaner, the wheels are likely blocked. Remove the blockage to resolve this issue.
General introduction to the robotic vacuum cleaner and its operating instructions.
Visual identification of robot, accessory, and remote control components through diagrams.
Essential safety guidelines to prevent injury and damage during product use.
Further safety advice on operation, temperature, battery, and environmental disposal.
Instructions for placing the charging station and charging the vacuum cleaner's battery.
Guide on operating the vacuum cleaner using the provided remote control.
Explanation of different cleaning modes: Automatic, Spot, Random, Edge, and Zigzag.
Steps for emptying the dust container and cleaning/washing the primary and HEPA filters.
Instructions for cleaning sensors, wheels, charging terminals, and vacuum port.
Guidance on checking, cleaning, and replacing the side brushes.
Key specifications including voltage, power, battery, dimensions, and noise level.
Common issues, their possible causes, and recommended actions for resolution.
General| Dust bag indicator | Yes |
|---|---|
| Telescopic tube | Yes |
| Cord length | 5 m |
| Dust bag volume | 3 L |
| Power | 700 W |
