What to do if oil is leaking from fittings on my MetalMaster PB-860T Industrial Equipment?
If you notice oil leaking from the fittings of your MetalMaster Industrial Equipment, the cause is likely loose fittings. You should tighten the fittings to resolve this issue.
Why doesn't the panbrake clamp work on my MetalMaster PB-860T Industrial Equipment?
If the panbrake clamp on your MetalMaster Industrial Equipment isn't working, several issues could be the cause. It could be due to a blocked pressure relief valve or directional valve, which would require cleaning. Alternatively, there might be a failure in either of these valves, necessitating a replacement. Other potential causes include a blocked suction filter (clean it), pump failure (check and replace if needed), or leakage in the pipes or cylinder (find and repair the leaks).
How to fix oil leaking from the cylinder of MetalMaster PB-860T?
If you observe oil leaking from the cylinder of your MetalMaster Industrial Equipment, the gland seal is likely damaged. You should change the seal to fix this.
Why is the material bend uneven on my MetalMaster Industrial Equipment?
If the material bend is uneven when using your MetalMaster Industrial Equipment, it might be due to several reasons. The clamp setting may be incorrect for the material thickness, in which case you should re-adjust the cam settings. Another reason might be that the finger edges are uneven, so you should adjust the pan clearance. Also, make sure you adjust the fingers.
What to do if the pan does not ascend on MetalMaster PB-860T?
If the pan on your MetalMaster Industrial Equipment does not ascend, it could be due to low pressure in the lifting cylinders, so you should check the system pressure. Alternatively, there might be leakage in the lifting cylinders, and you should replace the piston seal in this case.
What to do if MetalMaster PB-860T Industrial Equipment has no clamping?
If your MetalMaster Industrial Equipment isn't clamping, there are several potential causes. A blocked pressure relief valve or directional valve could be the issue; in this case, clean the valve. If the valves have failed, they should be changed. A blocked suction filter can also cause this, so clean the filter. Check the pump for failure and replace it if necessary. Look for any leakage in the pipes or cylinder and repair them. Finally, try pressing the reset button.
Why does the MetalMaster PB-860T Industrial Equipment apron not operate?
If the apron on your MetalMaster Industrial Equipment isn't operating, it could be due to low pressure in the lifting cylinders; check the system pressure. Another reason may be leakage in lifting cylinders, which requires replacing the piston seal. Alternatively, try pressing the Reset button.
How to fix uneven material bend in MetalMaster PB-860T Industrial Equipment?
An uneven material bend in MetalMaster Industrial Equipment can occur for several reasons. The clamp setting might be wrong for the material thickness, so re-adjust the cam settings. Uneven finger edges can also cause this; adjust the pan clearance. Also, make sure to adjust the fingers.
What to do if oil is leaking from the cylinder of MetalMaster PB-860T?
If oil is leaking from the cylinder of your MetalMaster Industrial Equipment, it is likely that the gland seal is damaged and needs to be changed.
How to stop oil from leaking from fittings in MetalMaster Industrial Equipment?
If oil is leaking from the fittings in your MetalMaster Industrial Equipment, the fittings are likely loose. Tighten the fittings to resolve the leak.
Detailed technical specifications for different Metalmaster Panbrake models, including dimensions and capacities.
Essential safety guidelines and precautions for operating the machinery safely.
Procedure for adjusting the clamp gap based on material thickness.
Common problems and their solutions for machine operation.
Guide to operating the machine using the NC-89 digital controller.
Instructions for using the machine's touch screen interface for bending operations.
Broad safety guidelines applicable to all machinery use.
Specific safety warnings and procedures for operating hydraulic panbrakes.
General| Model | PB-860T |
|---|---|
| Category | Industrial Equipment |
| Type | Plasma Cutting Machine |
| Working Gas | Compressed Air |
| Control System | CNC |
| Motor Power | 1.5 kW |
| Cutting Thickness | 0.5-25mm |
| Air Pressure | 0.4 - 0.8 MPa |
To Next Page
