137136
Turbocharged Engine Shutdown
After keeping the turbocharged engine
operating at high speed for a long time, please
firstly keep it idling for 3-5 min and then kill it,
so as to cool the turbocharger. Otherwise, the
turbocharger may get damaged due to
overheat.
The turbocharged engine shall not idle
for a long time. The idling time shall not
exceed 20 min.
Note
Other Control Instructions
1. Emergency start
Ÿ The brake or clutch switch failure will
make the start conditions unable to be
met, and thus the engine cannot start in
the normal procedures. You can firstly
turn the ignition switch at the ACC
position, confirm that the transmission is
at the neutral or P position, and then long
press the ENGINE START STOP switch
for 15s. In this case, emergency start of the
engine succeeds.
Ÿ Insufficient battery of the remote key may
cause the system to fail to search for the
key and thus the engine fails to start. In this
case, you can firstly depress the clutch
pedal (brake pedal for AT model), and at
the same time attach the side of remote
key close to the ENGINE START STOP
switch. When the green indicator on the
ENGINE START STOP switch illuminates,
press the switch to start the engine. Please
try again if you fail. You shall replace the
battery of the remote key.
ENGINE START STOP Function*
2. Emergency flameout
If emergency flameout of the engine is
required when the vehicle is running, you can
long press the ENGINE START STOP switch
for 2s or continuously press for 3 times
within 3s.
Never have a kid operate the ENGINE
START STOP switch in any case;
otherwise unexpected start or flameout
of the vehicle, and the vehicle damage
and the casualty accident may be caused.
Caution
Start Condition
Following conditions shall be met for engine
start:
1. The legal key is inside the vehicle;
2. Depress the clutch pedal (for MT model)
or brake pedal (for AT model).
If conditions above are met, the green
indicator on the ENGINE START STOP
switch will illuminate. In this case, if the gear is
at the neutral or P position, press the start
switch and the engine will immediately start.
Never operate the ENGINE START
STOP switch when the vehicle is running.
Acc iden tal v ehi cle fla meo u t m ay
suspend braking and assistance of the
steering system. In this case, the driver
will lose control of the vehicle and thus
the vehicle damage and the casualty
accident may be caused.
Caution
DRIVING AND CONTROLS
Cruise Control System *
Type-I Switch
Type-II Switch
As the switch of cruise control system is at the
steering wheel, when the cruise control
system is started, the vehicle can run at such
speed. Depress the brake pedal, and the
function will be immediately disabled. Except
that the brake pedal is used to disable the
function, operating switches such as parking
brake switch and clutch switch can also be
used to disable the function of the cruise
control system. The system can be used at 3, 4,
5 and 6 gears with the speed range of 40 Km/h
- 120 Km/h when the engine speed is lower
than 4800 rpm. For the AT model, the
minimum speed for starting the cruise control
system is 48 Km/h. Specific application
method:
First Step: Cruise Start
Based on the cruise control system switch
type, press the “ ” button or pull the toggle
button towards “ ” direction, and then the
cruise indicator on the instrument cluster
starts flickering, indicating that the cruise
control system enters the activated state; pull
the middle button towards the “SET/-”
direction, and the cruise start succeeds and
the cruise indicator of instrument is normally
on. (For example, when the driver intends to
stabilize the speed at 100 km/h, the driver
must firstly speed up to 100 km/h. When the
speed reaches 100 km/h, he/she shall press the
“ ” toggle button and then pull the toggle
button towards the “SET/-” direction. At this
time, release the accelerator pedal, and the
vehicle will continuously run at the speed of
100 km/h). After setting the cruising speed,
you can also use the accelerator pedal to
accelerate in the normal method; after the
accelerator pedal is released, the system will
recover the speed to the original cruising
speed.
Second Step: How to Deactivate Cruise
If you are to immediately decelerate in case of
any emergency in front during cruise control,
you can depress the brake pedal or clutch
pedal, or press the cruise deactivation button
“ ” or pull the toggle button towards “ ”
direction. In this case, the vehicle exits from
the current cruise state and enters the cruise
activation state, and the cruise indicator of
instrument flickers; if you press the “ ”
button in the cruise state, the whole cruise
system will be deactivated and the instrument
indicator will go out.
DRIVING AND CONTROLS
To Next Page
Loading...
Need help?
General
