QUICKGUIDE RALLY MIG 161i
UK
50113775 D
RALLY MIG 161i - Factory setting
Setting possibilities Area Step Factory setting Unit
2T
Primary parameters:
1 Welding current Area depends on
program
1 Depending on
program
A
Wire feed speed 0.1 m/min
Thickness of material 0.1 mm
2 Arc length -9.9 – +9.9 0.1 0.0 V
Secondary parameters:
1 Hotstart (MMA/TIG) 0 - 100 1 25 %
3 Arc power (MMA/TIG) 0 - 150 1 25 %
TIG process (TIG) ON/OFF OFF
1 Arc Adjust (MIG) -5.0 – +5.0 0.1 0.0 -
6 Burnback (MIG) 1 – 30 1 5 ms
Note: Fe programs with reversed polarity are recommended
for Innershield wires
Programs
No. Wire Material Gas
P106 Ø 0.6 mm Fe SG2 CO
2
P101 Ø 0.8 mm Fe SG2 CO
2
P109 Ø 0.9 mm Fe SG2 CO
2
P102 Ø 1.0 mm Fe SG2 CO
2
P116 Ø 0.6 mm Fe SG2 ArCO
2
(82/18)
P111 Ø 0.8 mm Fe SG2 ArCO
2
(82/18)
P119 Ø 0.9 mm Fe SG2 ArCO
2
(82/18)
P112 Ø 1.0 mm Fe SG2 ArCO
2
(82/18)
P201 Ø 0.8 mm CrNi ER 316 LSI ArCO
2
(98/2)
P209 Ø 0.9 mm CrNi ER 316 LSI ArCO
2
(98/2)
P202 Ø 1.0 mm CrNi ER 316 LSI ArCO
2
(98/2)
P311 Ø 0.8 mm AlMg5 ER5356 Ar
P319 Ø 0.9 mm AlMg5 ER5356 Ar
P312 Ø 1.0 mm AlMg ER5356/ER5554 Ar (100)
P359 Ø 0.9 mm AlSi5 ER4043 Ar (100)
P352 Ø 1.0 mm AlSi5 ER4043 Ar
P369 Ø 0.9 mm AlMg3Mn ER5554 Ar (100)
P372 Ø 1.0 mm AlSi12 ER4047 Ar (100)
P501 Ø 0.8 mm CuAl8 Brazing ArCO
2
(98/2)
P509 Ø 0.9 mm CuAl8 Brazing ArCO
2
(98/2)
P502 Ø 1.0 mm CuAl8 Brazing ArCO
2
(98/2)
P561 Ø 0.8 mm CuSi3 Brazing ArCO
2
(98/2)
P569 Ø 0.9 mm CuSi3 Brazing Ar (100)
P562 Ø 1.0 mm CuSi3 Brazing ArCO
2
(98/2)
Arc adjust (electronic choke)
1
Set welding current (A)
Burnback
MIG parameters
Set welding
current (A)
Hotstart
Arc
power
Short circuit
MMA parameters
TIG
welding
To Next Page
Need help?
General
