Migatronic MIG 445 MK III User Manual

8 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

MIG 385/445/545 MK III

Brugsanvisning

Instruction manual

Betriebsanleitung

Manuel d'instruction

Gebruikershandleiding

Manuale d'istruzione

Bruksanvisning

Käyttöohje

Manual de instrucciones

Kezelési útmutató

Valid from 2011 week 20 50115308 L

Table of Contents

Questions and Answers:

M
Misty ArmstrongAug 8, 2025
Why has the wire feed stopped on my Migatronic MIG 445 MK III Welding System?
- C
  conniemillerAug 8, 2025
  If the wire feed stops on your Migatronic Welding System, several factors could be at play. First, check that the inlet nozzle and the wire are correctly aligned. Ensure the reel of wire isn't too taut, allowing the wire to come off evenly. Inspect the inlet tube or contact tip for wear or blockages. Verify the welding wire is clean, rust-free, and of good quality. Finally, ensure the pressure roller is adequately tightened.
S
sean90Aug 18, 2025
How to fix wire sticking in the contact tip of Migatronic MIG 445 MK III Welding System?
- V
  Victoria OrtizAug 18, 2025
  If the wire keeps sticking in the contact tip and feeds slowly on your Migatronic Welding System, cut off any damaged wire, pull it out, and replace it. Also, a worn out contact tip can cause this issue. Check and adjust the pressure on the wire feed roller as needed.
R
Rachel ThompsonAug 28, 2025
What to do if I have porous weld with Migatronic Welding System?
- T
  tannerdebraAug 28, 2025
  A porous weld or cone formation during spot welding with your Migatronic Welding System could be due to a blocked contact tip. Another cause might be a leak in the gas hose, drawing in air that mixes with the shielding gas.

Migatronic MIG 445 MK III Specifications

General

Brand	Migatronic
Model	MIG 445 MK III
Category	Welding System
Language	English

Summary

SAFETY WARNINGS

Electricity Safety

Proper installation and handling related to electrical hazards.

Light and Heat Emissions

Welding Smoke and Gases

Fire Hazard

DESCRIPTION OF FUNCTIONS

INITIAL OPERATION

Mains Connection and Safety

Instructions for connecting to the power supply and thermal cut-out.

Gas and Earth Cable Connection

OPERATIONAL PROCEDURES AND CONTROLS (S-MODEL)

Welding Torch and Wire Feed Unit Setup

S-MODEL Control Panel Overview

Explanation of switches and indicators on the S-model control panel.

OPERATIONAL PROCEDURES AND CONTROLS (C-MODEL)

C-MODEL Control Panel Overview

Explanation of switches and indicators on the C-model control panel.

MAINTENANCE

Wire Feed Unit Maintenance

ERROR AND TROUBLESHOOTING

Machine Overheat Error

Identifying, understanding, and resolving overheating issues.

Wire Feed Problems

Troubleshooting steps for a stopped wire feed.

Spatter Issues

Porous Weld Troubleshooting

Wire Sticking

Resolving issues with wire sticking in the contact tip.

Related product manuals

Preview: Migatronic MIG 385 MK III

Migatronic MIG 385 MK III

Migatronic MIG 545 MK III

Preview: Migatronic MIG 385x S

Migatronic MIG 385x S

Preview: Migatronic MIG 305x C

Migatronic MIG 305x C

Preview: Migatronic MIG 300 STB

Migatronic MIG 300 STB

Migatronic RALLY MIG 160

Preview: Migatronic RALLY MIG 161i

Migatronic RALLY MIG 161i

Migatronic MIGMAN 385

Preview: Migatronic PILOT 2000

Migatronic PILOT 2000

Preview: Migatronic AUTOMIG2 i

Migatronic AUTOMIG2 i

Preview: Migatronic Focus Tig 200 AC/DC

Migatronic Focus Tig 200 AC/DC

Preview: SIGMA2 300 STBOFF SHORE

SIGMA2 300 STBOFF SHORE