MikroTik Wireless Wire Cube User Manual (English)

To Next Page

Wireless Wire Cube

Wireless Wire Cube (CubeG-5ac60adpair)

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.

This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate

measures.

Exposure to Radio Frequency Radiation:This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an

uncontrolled environment.This MikroTik device should be installed and operated no closer than 21 centimeters from your body, occupational user, or the

general public.

Quickstart

Connect the device to the included PoE injector with Ethernet cable;

Connect the PoE injector into the PC or to the network switch;

Connect the power adapter to the PoE injector;

Download WinBox configuration tool ;https://mt.lv/winbox

Open WinBox and connect to the device;

Default IP: 192.168.88.2/192.168.88.3, user name:

admin

, please find the password on the sticker;

Download the latest RouterOS software from ;https://mikrotik.com/download

Choose ARM packages, and save them to your PC;

Open WinBox and upload downloaded packages, drag and drop into any windows;

Restart the device;

Connect again and select your Region in the Wireless menu, W60G tab, and in menu set your Country, to apply country regulation

QuickSet

settings.

If device RX blocking condition has happened device will restore its signal after a few seconds.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

Note. The information contained here is subject to change. Please visit the product page on www.mikrotik.com for the most up to date version of

this document.

Need help?

Do you have a question about the MikroTik Wireless Wire Cube and is the answer not in the manual?

MikroTik Wireless Wire Cube Specifications

General

Flash memory	16 MB
Internal memory	256 MB
Processor model	IPQ4019
Built-in processor	Yes
Processor frequency	716 MHz
Processor manufacturer	Qualcomm
Operating system installed	RouterOS
2.4 GHz	No
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11n, IEEE 802.3af, IEEE 802.3at
Receiver sensitivity	-93 (6MBit/s), -74 (54MBit/s), -93 (MCS0), -71 (MCS7), -68 (MCS9)
Maximum outdoor range	800 m
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Mean time between failures (MTBF)	200000 h
Maximum data transfer rate (5 GHz)	433 Mbit/s
Operating temperature (T-T)	-40 - 70 °C
Placement	Pole, Wall
Certification	CE, FCC, IC, EAC, RoHS
Product color	White
Output current	0.8 A
Output voltage	24 V
AC input voltage	12 - 57 V
Power consumption (max)	9 W
Antenna type	Internal
Antenna gain level (max)	11.5 dBi
Number of products included	1 pc(s)
USB 2.0 ports quantity	0
Ethernet LAN (RJ-45) ports	1
Security algorithms	-