EasyManua.ls Logo

Mile Marker PE5000 - User Manual

Mile Marker PE5000
16 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Installation & Operator’s
Manual
PE5000
5,000 lbs.
77-50120W (STEEL CABLE)
77-53120W (SYNTHETIC ROPE)
2121 BLOUNT ROAD
POMPANO BEACH, FL 33069 USA
MILEMARKER.COM
INFO@MILEMARKER.COM
800.886.8647

Table of Contents

Questions and Answers

  • E
    Emily HughesAug 4, 2025
    What to do if Mile Marker Winches motor does not turn on?
    • P
      Patricia BrownAug 4, 2025
      If the motor of your Mile Marker Winches doesn't turn on, there are several potential causes and solutions: * Ensure the Safety Switch is in the ON position. * Check that the Switch assembly is firmly connected to the connector. * Tighten any loose nuts on the battery cable connectors. * Try tapping the solenoid to free the contact while applying 12 volts directly to the coil terminal to check for an audible click. * Consider replacing the Switch assembly if it's defective. * Check for voltage at the armature port with the switch pressed; if voltage is present, the motor may need replacement. * If water has entered the motor, drain and dry it, then run it in short bursts without load until completely dry.
  • H
    Heather BrownAug 9, 2025
    Why does Mile Marker Winches motor run slowly or without normal power?
    • B
      Billy HernandezAug 9, 2025
      If your Mile Marker Winches motor runs slowly or lacks normal power, it could be due to a discharged battery. Recharge the battery by running the vehicle engine. Alternatively, there might be insufficient current or voltage, in which case you should clean, tighten, or replace the connector.
  • P
    Pam MathisAug 15, 2025
    What to do if Mile Marker Winches motor runs in one direction only?
    • R
      Robert PhillipsAug 15, 2025
      If your Mile Marker Winches motor only runs in one direction, the issue might stem from a defective or stuck solenoid. Try tapping the solenoid to free the contacts. If that doesn't work, consider repairing or replacing the solenoid. Another potential cause is a defective switch assembly, which would need to be replaced.
  • B
    Brian OsbornAug 22, 2025
    How to handle Mile Marker Winches motor that runs too hot?
    • S
      Shannon WallerAug 22, 2025
      If the motor of your Mile Marker Winches runs too hot, it's likely due to a long period of operation. To resolve this, let the winch cool down periodically.
  • K
    Kimberly JohnsonAug 27, 2025
    What to do if Mile Marker Winches motor runs but cable drum does not turn?
    • K
      kfischerAug 28, 2025
      If the motor of your Mile Marker Winches runs, but the cable drum doesn't turn, ensure that the clutch is fully engaged by turning the Clutch Gear to the IN/ENGAGED position. If engaging the clutch doesn't solve the problem, it's recommended to have a qualified technician inspect and repair the winch.

Summary

Safety Warnings

Precautions

Getting Started

Mounting Options

Discusses various mounting points and considerations for winch installation.

Winch Mounting

Steps for securely installing the winch onto the vehicle or mounting bracket.

Wiring Instructions

Winch Operation

Function Testing

Guide to testing winch functions after installation and connection.

Winching Tips & Techniques

Winching Tips and Use of a Snatch Block

Advice on using snatch blocks and general winching best practices.

Rating

Specifies limits for cable pull direction to avoid overloading.

Safety Tips

Important safety advice during winching operations.

Self Recovery

Use of a Pulley Block or Snatch Block

Use of a Nylon Sling and Shackle

Motor Temperature

Spooling Under Load

Rigging

Winch Maintenance

Troubleshooting

Parts Breakdown & Assembly (Steel Cable)

Parts Breakdown & Assembly (Synthetic Rope)

Warranty

Mile Marker PE5000 Specifications

General IconGeneral
Rated Line Pull5000 lbs
Cable Length100 ft
Cable Diameter3/8 in
FairleadRoller
Line Length100 ft
Line Diameter3/8 in
TypeElectric

Related product manuals