Mitsubishi Electric HC5000 User Manual (English)

Other manuals for Mitsubishi Electric HC5000

Questions and Answers:

W
wturnerAug 22, 2025
Why does my Mitsubishi Electric HC5000 have no image on the screen?
- B
  byrdbrianAug 22, 2025
  If no image appears on the screen of your Mitsubishi Electric Projector, make sure the lens cap is removed. Allow about one minute for the lamp to light up. If the lamp doesn't light, wait a few minutes and try again. If the projector was turned off before the lamp cooled, the fan may start, and the POWER button may not work. Wait for the fan to stop, then press the POWER button. Ensure the intake vent is clean and that the lamp cover is closed. Also, verify the cables connected to external devices are not broken. If using an extension cable, replace it with the supplied cable to check; if images display correctly, add an RGB signal amplifier. Finally, check the operation manual of the video device for connection instructions and set SCART INPUT in the FEATURE menu to OFF.
A
Aaron MonroeSep 1, 2025
What causes fine streaks on my Mitsubishi Electric Projector images?
- J
  Jonathan RubioSep 1, 2025
  Fine streaks on projected images from your Mitsubishi Electric Projector are due to interference with the screen surface and are not a malfunction. Try replacing the screen or slightly displacing the focus. Additionally, vertical or horizontal streak noise may appear depending on the DVD player or game console used; enable the LPF to reduce this noise.
P
Pam ArmstrongAug 31, 2025
Why are my Mitsubishi Electric Projector images dark?
- R
  Richard SpenceAug 31, 2025
  If the projected images from your Mitsubishi Electric Projector are dark, adjust BRIGHTNESS and CONTRAST in the IMAGE menu. If the issue persists, replace the lamp.
Z
zachary16Aug 30, 2025
Why is my Mitsubishi Electric HC5000 image distorted?
- L
  Lisa NguyenAug 30, 2025
  If the projected images from your Mitsubishi Electric Projector are distorted, adjust the projector and the screen so that they are perpendicular to each other.
L
Lisa RogersAug 28, 2025
What to do if my Mitsubishi Electric Projector shows a password screen?
- A
  adkinskatrinaAug 29, 2025
  If the screen for entering the password appears on your Mitsubishi Electric Projector, it means the PASSWORD FUNCTION in the FEATURE menu has been set to DISPLAY INPUT. Enter the password or contact the person in charge of management of the projector.
S
Susan MyersAug 27, 2025
How to fix blurred images on Mitsubishi Electric HC5000?
- W
  William JohnsonAug 27, 2025
  To fix blurred images on your Mitsubishi Electric Projector, adjust the focus. Clean the lens. Press the W or X button on the remote control to eliminate flicker. Adjust TRACKING and FINE SYNC in the SIGNAL menu. Adjust BRIGHTNESS and CONTRAST in the IMAGE menu. Ensure the projector and screen are perpendicular to each other.
H
holly76Aug 26, 2025
How to fix shaking images on Mitsubishi Electric Projector?
- S
  Stephanie AlvarezAug 27, 2025
  If the projected images from your Mitsubishi Electric Projector are shaking or displaced, check that the cable connected to the external device isn’t intermittent and connect the cable’s plug with the external device’s connector firmly. You can also press the AUTO POSITION button. If you still experience the issue, it may be due to out-of-spec signals from some computers; in this case, adjust the SIGNAL menu.
N
Nicholas CisnerosAug 25, 2025
Why does my Mitsubishi Electric Projector display 'NO SIGNAL'?
- L
  lpettyAug 26, 2025
  If your Mitsubishi Electric Projector displays 'NO SIGNAL', turn on the connected device and ensure it's working correctly. Check that the external device outputs signals, especially if it's a notebook computer. Verify the cable connecting the external device isn't defective and that the projector is connected using the correct terminals. Ensure the connected device is correctly selected as the input source. If using an extension cord, replace it with the supplied cable to check if images are projected correctly; if so, use an RGB signal amplifier with the extension cord.
D
David ComptonAug 25, 2025
What to do if my Mitsubishi Electric HC5000 power turns off by itself?
- J
  Johnny KelleyAug 25, 2025
  If your Mitsubishi Electric Projector turns off, this may occur when the intake vent and/or exhaust vents are blocked. Remove any obstructions, wait for the intake/exhaust fan to stop (until the STATUS indicator goes out), unplug the power cord, wait 10 minutes, plug it back in, and press the POWER button. If the STATUS indicator is steady red, replace the lamp. Also, verify that AUTO POWER OFF is set to OFF. Note that if the lamp has deteriorated, it may go out after illuminating for a while.

Mitsubishi Electric HC5000 Specifications

General

Resolution	1920 x 1080
Brightness	1000 ANSI lumens
Contrast Ratio	10000:1
Lamp Life	3000 hours
Projection Size	40 - 300 inches
Contrast Ratio (dynamic)	10000:1
Input Connectors	HDMI, Composite