Mitsubishi Electric LE-40MT Series - Comparison of I;O Terminal Blocks

2 TRANSITION FROM LE-40MTA, B(-E) TO LE7-40GU-L
2.2 Comparison of I/O Terminal Blocks
11
2
2.2 Comparison of I/O Terminal Blocks
Perform wiring by referring to the comparison between the I/O terminal blocks of LE-40MTA, B(-E) and LE7-40GU-L.
For the wiring method, refer to the following.
LE7-40GU-L APPLICATION MANUAL
Item name LE-40MTA, B(-E) LE7-40GU-L
Function Terminal Specifications Terminal Specifications
Power
supply
Input PSL 100 to 240 V AC (-15% to +10%) 50/60 Hz
Power consumption 400 VA, built-in power fuse
250 V, 8 A
Rush current 30 A 300 ms, momentary power
failure permissible time 10 ms
L 100 to 240 V AC (-15 to +10%) 50/60 Hz
Maximum apparent power 200 VA, built-in power
fuse 250 V, 8 A2
Rush current 45 A 1 ms, momentary power failure
permissible time 10 ms
PSN N
Output RED Tension detector power
5 V DC, 40 mA or less
Up to two LX tension detectors can be connected.
RED Tension detector power
• The rated voltage: 5 V DC
• Voltage range: 4.75 to 5.25 V DC
• Current value: 40 mA or less
• Up to two LX tension detectors can be
connected.
BLK BLK
+5V Service power supply for external control
Output voltage: 5 0.2 V DC 5 V DC 50 mA or less
5V Potentiometer power
• The rated voltage: 5 V DC
• Voltage range: 4.75 to 5.25 V DC
• Current value: 20 mA or less
• Available volume: 0.5 to 2.0 k
AIC AIC
 24V Contact input power
• The rated voltage: 24 V DC
• Voltage range: 20.4 to 28.8 V DC
• Current value: 55 mA or less
 0V
Control Output P Tension control output for 24 V DC series powder
clutch/brake
0 to 24 V DC 4 A or less
PP Tension control output for 24 V DC series powder
clutch/brake
• 0 to 24 V DC
•2.7 A or less
• PWM output
NPN
S1 Auxiliary power supply
12 V DC 2 A 10 seconds rated
S1 Two-reel's switching new reel output for 24 V DC
powder clutch/brake
• 0 to 24 V DC
• The total current value with PP-PN output is 2.7
A or less.
• PWM output
S2 S2
SA Control output signal
0 to 5 V DC when "powder" is selected
0 to 5 V DC when "servomotor" is selected
Load resistance: 1 k or more
SA Tension control output for motor
• Output range switchable
(1) -5 to +5 V DC resolution: Approx. 358 V
(2) -8 to +8 V DC resolution: Approx. 358 V
(3) -10 to +10 V DC resolution: Approx. 358 V
(4) -2.7 to +2.7 V DC resolution: Approx. 358 V
(5) 0 to 5 V DC resolution: Approx. 358 V
(6) 0 to 8 V DC resolution: Approx. 358 V
(7) 0 to 10 V DC resolution: Approx. 358 V
(8) 0 to 2.7 V DC resolution: Approx. 358 V
• Load resistance: 1 k or more
SN SN
NRO New-reel preset output (enabled only when multi-
reel mode is selected)
0 to 5 V DC
Load resistance: 1 k or more
NRO Two-reel's switching new reel output for motor
• Output range switchable
(1) -5 to +5 V DC resolution: Approx. 358
V
(2) -8 t
o +8 V DC resolution: Approx. 358 V
(3) -10 to +10 V DC resolution: Approx. 358 V
(4) -2.7 to +2.7 V DC resolution: Approx. 358 V
(5) 0 to 5 V DC resolution: Approx. 358 V
(6) 0 to 8 V DC resolution: Approx. 358 V
(7) 0 to 10 V DC resolution: Approx. 358 V
(8) 0 to 2.7 V DC resolution: Approx. 358 V
• Load resistance: 1 k or more
AOC SN
EAP Tension control signal output for electro-pneumatic
regulator
4 to 20 mA DC or less
Load resistance: 470  or less
EAP Tension control output for electro-pneumatic
regulator
• 0 to 20 mA DC resolution: Approx. 1.43 A
• Load resistance: 500  or less
EAN EAN