Need help?Do you have a question about the Mitsubishi Electric MELSEC iQ-RJ71C24-R2 and is the answer not in the manual?
General| Type | Communication Module |
|---|---|
| Product Type | Communication Module |
| Compatible Series | MELSEC iQ-R Series |
| Series | iQ-R |
| Number of Ports | 2 |
| Number of Channels | 2 |
| Power Supply Voltage | 5 VDC |
| Weight | 0.2 kg |
| Operating Temperature | 0 to 55 °C |
| Storage Temperature | -25 to 75 °C |
| Operating Humidity | 5 to 95% RH (non-condensing) |
| Dielectric Strength | 500 V AC for 1 minute |
| Product Category | Controller |
| Interface | RS-232/RS-422/RS-485 |
| Communication Standard | RS-232/RS-422/RS-485 |
| Protocols Supported | MELSEC Communication Protocol |
| Dimensions | 27.6 mm x 98 mm x 90 mm |
| Vibration Resistance | 5 to 9 Hz, amplitude 3.5 mm; 9 to 150 Hz, acceleration 9.8 m/s² |
| Shock Resistance | 147 m/s², 3 times in each of 3 axes |
| Noise Immunity | 1500 Vp-p |
| Insulation Resistance | 10 MΩ or more at 500 VDC |
Indicates hazardous conditions that may result in death or severe injury if handled incorrectly.
Shut off external power supply before mounting or removing the module to prevent electric shock.
Ground FG and LG terminals with resistance of 100 ohms or less to prevent electric shock or malfunction.
Do not touch any terminal while power is on to prevent electric shock or malfunction.
Handle modules carefully to avoid static electricity discharge, which may cause failure or malfunction.
Treat the product as industrial waste and dispose of batteries separately according to local regulations.
Follow transportation regulations for lithium batteries and consider disinfection methods for packaging to prevent product failure.
Explains how to read/write device data and programs to/from the CPU module via C24 using MC protocol.
Describes data transmission/reception using protocols appropriate to the target device.
Explains arbitrary data format and transmission control procedure for data communication between CPU and target device.
Explains data transfer between target device and CPU using data format and transmission control for bidirectional protocol.
Supports debugging of communication processing between C24 and target device.
Explains CPU monitoring function where C24 monitors the controller CPU based on user-registered monitoring info.
Explains the modem function for data communication with remote target devices via public lines.
Explains data reception using an interrupt program for nonprocedural or bidirectional protocol communication.
Explains how to change data length units (word to byte, byte to word) for data communication.
Explains monitoring time for receiving interval, CPU processing, and transmission.
Explains transmission control function for C24 and target device using DC codes.
Explains settings to prevent simultaneous transmission for half-duplex communications via RS-232 interface.
Explains data that can be registered, contents transmitted/received, and how C24 handles user frames.
Explains transmission of data specified by CPU module using message format other than standard formats.
Explains data transmission/reception methods and procedures when communication data using user frames with nonprocedural protocol.
Explains handling of transparent codes and additional codes during data communication using nonprocedural or bidirectional protocol.
Explains ASCII-binary conversion for transmitting/receiving data in ASCII code to/from a target device.
Explains data communications between target devices and CPU module by multidrop connection.
Forcefully switches communication protocol and transmission specifications of a designated interface.
Describes C24 send/receive data monitoring function for debugging programs.
Explains the independent and linked operation of C24 interfaces.
Explains how C24 enables parameter settings to be saved in the CPU module.
Explains the echo back enable/prohibit specification for RS-422/485 interface.
Explains the erroneous noise signal reception prevention function of C24.
Explains the automatic removal of NULL characters in data transmission of C24.
Explains parameter settings necessary for data communication between C24 and a target device.
Explains errors that may occur and their corrective actions.
To Next Page
