Mitsubishi A1SD75M3

Index - 1
INDEX
[Number]
1-axis fixed-dimension feed control.............. 9-29
1-axis linear control (ABS linear 1) ............... 9-23
1-axis linear control (INC linear 1) ................ 9-24
17-segment LED ............................................. 4-3
2-SPEED TRAPEZOIDAL CONTROL
(explanation of terms) ...................... Appendix-32
2-axis circular interpolation control with auxiliary
point designation (ABS circular interpolation)
....................................................................... 9-34
2-axis circular interpolation control with auxiliary
point designation (INC circular interpolation)
....................................................................... 9-37
2-axis circular interpolation control with center
point designation (ABS right arc, ABS left arc)
....................................................................... 9-42
2-axis circular interpolation control with center
point designation (INC right arc, INC left arc)
....................................................................... 9-44
2-axis fixed-dimension feed control (interpolation)
....................................................................... 9-31
2-axis linear interpolation control (ABS linear 2)
....................................................................... 9-25
2-axis linear interpolation control (INC linear 2)
....................................................................... 9-27
[A]
ABSOLUTE ENCODER (explanation of terms)
..........................................................Appendix-32
ABSOLUTE POSITION DETECTION SYSTEM
(explanation of terms) ...................... Appendix-32
ABSOLUTE SYSTEM (explanation of terms)
..........................................................Appendix-32
ACCELERATION TIME (explanation of terms)
..........................................................Appendix-32
Actual acceleration/deceleration time........... 5-26
AD75..............................................................A-16
AD75 READY signal ..................................... 3-13
AD75 software package.........................A-16, 2-4
ADDRESS (explanation of terms) ... Appendix-33
AFTER mode............................................... 12-79
AFTER mode (explanation of terms)
..........................................................Appendix-33
AUTO TUNING (explanation of terms)
..........................................................Appendix-33
AUTOMATIC TRAPEZOIDAL ACCELERATION/
DECELERATION (explanation of terms)
...........................................................Appendix-33
Absolute position restoration function .........12-58
Absolute position restoration mode... 9-18, 12-65
Absolute position restoration mode (
Md.121
)
......................................................................5-166
Absolute position restoration mode switching
function.........................................................12-65
Absolute position restoration selection (
Pr.59
)
........................................................................5-57
Absolute system.............................................9-13
Acceleration / deceleration time change program
........................................................................6-17
Acceleration time 0 (
Pr.8
).........................5-26
Acceleration time 1 (
Pr.26
).........................5-38
Acceleration time 2 (
Pr.27
).........................5-38
Acceleration time 3 (
Pr.28
).........................5-38
Acceleration time No. (
Da.3
) ...................5-115
Acceleration/deceleration process selection
(
Pr.35
)..........................................................5-40
Acceleration/deceleration processing function
......................................................................12-95
Acceleration/deceleration time change during
speed change, enable/disable selection (
Cd.35
)
......................................................................5-184
Acceleration/deceleration time change function
......................................................................12-53
Address (
Da.16
).........................................5-134
Advanced positioning control ........................10-2
Allowable circular interpolation error width
(
Pr.42
)..........................................................5-44
Amplifier setting (
Pr.101
) .. 5-59, 68, 78, 89, 104
Applicable system............................................2-6
Applicable wire size .........................................3-3
Arc address (
Da.6
)...................................5-120
Assembling the connector section ................4-15
Automatic trapezoidal acceleration/deceleration
processing method ......................................12-96
Auto tuning (
Md.105
)...................................5-160
Auto tuning (
Pr.108
).......... 5-61, 71, 80, 91, 107
Auxiliary functions..........................................12-2
Auxiliary functions specifically for machine zero
point returns ...................................................12-4
Axis display LED..............................................4-4