Mitsubishi A1SD75M3

Index - 2
Axis error No. (
Md.20
,
Md.33
)........... 5-142, 146
Axis error occurrence time (Hour: minute)
(
Md.21
)....................................................... 5-142
Axis error occurrence time (Second: 100 ms)
(
Md.22
)....................................................... 5-142
Axis error reset (
Cd.12
)............................. 5-174
Axis feedrate (
Md.37
) ................................ 5-150
Axis in which the error occurred (
Md.19
).. 5-142
Axis in which the warning occurred (
Md.24
)
..................................................................... 5-144
Axis monitor data......................................... 5-146
Axis operation status (
Md.35
).................... 5-148
Axis stop signal ............................................. 3-14
Axis warning No. (
Md.25
,
Md.34
) ..... 5-144, 148
Axis warning detection ................................ 5-152
Axis warning occurrence time (Hour: minute)
(
Md.26
)....................................................... 5-144
Axis warning occurrence time (Second: 100 ms)
(
Md.27
)....................................................... 5-144
[B]
BACKLASH COMPENSATION
(explanation of terms) ...................... Appendix-33
BACKUP FUNCTION (explanation of terms)
..........................................................Appendix-33
BALL SCREW (explanation of terms)
..........................................................Appendix-34
BIAS SPEED AT START (explanation of terms)
..........................................................Appendix-34
BUSY (explanation of terms) ...........Appendix-34
BUSY signal .................................................. 3-13
Backlash compensation amount (
Pr.12
) ... 5-28
Backlash compensation function................ 12-13
Basic parameters 1 ....................................... 5-22
Basic parameters 2 ....................................... 5-26
Bias speed at start (
Pr.10
) ......................... 5-27
Block .............................................................. 10-8
Block No. being executed (
Md.55
)............ 5-158
Block start (normal start)............................... 10-8
Block transmission ........................................ 7-16
Block transmission area.................................. 7-3
Buffer memory................................................. 7-2
Buffer memory area configuration .................. 7-5
[C]
CCW (explanation of terms) ............Appendix-34
CHANGE signal (explanation of terms)
..........................................................Appendix-34
CIRCULAR INTERPOLATION
(explanation of terms).......................Appendix-34
COMPOSITE SPEED (explanation of terms)
...........................................................Appendix-34
CONTINUOUS POSITIONING CONTROL
(explanation of terms).......................Appendix-34
CONTROL UNIT (explanation of terms)
...........................................................Appendix-34
CP CONTROL (explanation of terms)
...........................................................Appendix-34
CPU module.....................................................2-6
CREEP SPEED (explanation of terms)
...........................................................Appendix-35
CURRENT FEED VALUE (explanation of terms)
...........................................................Appendix-35
CURRENT LOOP MODE (explanation of terms)
...........................................................Appendix-35
CURRENT VALUE (explanation of terms)
...........................................................Appendix-35
CURRENT VALUE CHANGE
(explanation of terms).......................Appendix-35
CW (explanation of terms)................Appendix-35
Cable clamp ...................................................4-10
Cable fixture...................................................4-12
Clock data (hour: minute) (
Md.5
).............5-136
Clock data (second: 100 ms) (
Md.6
) .......5-136
Clock data function ......................................13-11
Clock data setting (hour) (
Cd.1
) ..............5-168
Clock data setting (minute, second) (
Cd.2
)
......................................................................5-168
Clock data setting program............................6-14
Clock data writing (
Cd.3
) .........................5-168
Combination of AD75 functions.....................3-10
Combination of main functions and auxiliary
functions.........................................................3-10
Command in-position flag............................5-152
Command in-position function.....................12-92
Command in-position width (
Pr.17
)............5-30
Command speed (
Da.7
) ..........................5-124
Command speed ...........................................1-11
Common functions................................. 3-9, 13-1
Communicating signals between AD75 and each
module............................................................1-12
Composite speed...........................................5-35
Condition data..............................................10-17
Condition operator .......................................10-18
Condition operator (
Da.15
)........................5-134
Condition start..............................................10-10