Mitsubishi A1SD75M3

Index - 3
Condition target (
Da.14
)............................ 5-134
Conditional JUMP ......................................... 9-62
Configuration and roles of AD75 memory...... 7-2
Confirming the current value......................... 9-14
Confirming the installation and wiring........... 4-16
Conformation to the EMC Directive and Low
Voltage Instruction.........................................A-12
Connecting the connector and wire.............. 4-13
Connection connector ..................................... 3-3
Connector...................................................... 4-12
Connector cover............................................ 4-12
Continuous operation interrupt program....... 6-19
Continuous path control.................................. 9-7
Continuous positioning control........................ 9-6
Control data area............................................. 7-3
Control functions ............................................. 3-4
Control method (
Da.2
)............................. 5-115
Count method 1) machine zero point return
....................................................................... 8-11
Count method 2) machine zero point return
....................................................................... 8-14
Count method 3) machine zero point return
....................................................................... 8-16
Creep speed (
Pr.49
)................................... 5-52
Current feed value......................................... 9-14
Current feed value (
Md.29
)........................ 5-146
Current feed value during speed control (
Pr.22
)
....................................................................... 5-35
Current speed (
Md.36
) .............................. 5-148
Current value change.................................... 9-57
[D]
DATA NO. (explanation of terms)....Appendix-35
DECELERATION RATIO (explanation of terms)
..........................................................Appendix-35
DECELERATION TIME (explanation of terms)
..........................................................Appendix-35
DEVIATION COUNTER (explanation of terms)
..........................................................Appendix-36
DOG SIGNAL (explanation of terms)
..........................................................Appendix-36
DOS/V personal computer............................A-16
DROOP PULSE (explanation of terms)
..........................................................Appendix-36
DWELL TIME (explanation of terms)
..........................................................Appendix-36
DYNAMIC BRAKE (explanation of terms)
..........................................................Appendix-36
Data link system............................................ A-16
Data setting method machine zero point return
........................................................................8-18
Data transmission process ..............................7-6
Deceleration stop...........................................6-37
Deceleration time 0 (
Pr.9
).........................5-26
Deceleration time 1 (
Pr.29
).........................5-38
Deceleration time 2 (
Pr.30
).........................5-38
Deceleration time 3 (
Pr.31
).........................5-38
Deceleration time No. (
Da.4
)...................5-115
Detailed parameters 1 ...................................5-28
Detailed parameters 2 ...................................5-38
Details of input signals (AD75
PLC CPU)
........................................................................3-13
Details of output signals (PLC CPU
AD75)
........................................................................3-14
Deviation counter droop pulse amount .........1-11
Deviation counter value (
Md.102
)...............5-160
Disassembling the connector section ...........4-12
Disposal instructions......................................4-20
Dwell time/JUMP designation positioning data No.
(
Da.8
)........................................................5-126
Dwell time during zero point return retry (
Pr.58
)
........................................................................5-57
[E]
ELECTROMAGNETIC BRAKE
(explanation of terms).......................Appendix-36
EMERGENCY STOP (explanation of terms)
...........................................................Appendix-36
ENCODER (explanation of terms) ...Appendix-37
ERROR CORRECTION (explanation of terms)
...........................................................Appendix-37
ERROR RESET (explanation of terms)
...........................................................Appendix-37
EXTERNAL REGENERATIVE BRAKE
RESISTOR (explanation of terms)...Appendix-37
Effective load ratio (
Md.118
) .......................5-166
Electrical specifications..................................3-15
Electronic gear function ...............................12-15
Emergency stop.............................................6-36
Encoder output pulses (
Pr.138
).................5-102
Error and warning details...............................14-2
Error codes
Detected by AD75......................................14-6
Detected by MR-H-B (MR-H-BN) ............14-26
Detected by MR-J-B.................................14-34
Detected by MR-J2-03B5 ........................14-58