Mitsubishi MELSEC Q Series Structured Programming Manual

Mitsubishi MELSEC Q Series

268 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Page #241 background image

Loading...

Page #241 background image

5.12 Standard Timer Function Blocks

5.12.1 Pulse timer

5-207

5

APPLICATION

FUNCTIONS

TP(_E),

TP_HIGH(_E)

TP(_E), TP_HIGH(_E)

Operation Error

No operation error occurs in the execution of the TP (_E) function.

Program Example

The program which turns ON bit type data of for 10 seconds after bit type data input to is

turned ON.

(a) Function without EN/ENO (TP)

[Structured ladder]

[ST]

TP_Inst (g_bool1, T#10s, g_bool2, g_time1);

(b) Function with EN/ENO (TP_E)

[Structured ladder]

[ST]

TP_E_Inst (g_bool1, T#10s, g_bool2, g_time1);

d1

s

Table of Contents

Other manuals for Mitsubishi MELSEC Q Series

User Manual664 pages

Programming Manual1296 pages

Handbook130 pages

Questions and Answers:

E
Elizabeth RoseAug 25, 2025
What to do if the input signal is not turned OFF on my Mitsubishi MELSEC Q?
- A
  allisonalexanderAug 26, 2025
  If the input signal on your Mitsubishi Controller isn't turning OFF, it could be due to leakage current from the input switch. To resolve this, connect an appropriate resistor to lower the voltage across the input module terminals below the OFF voltage value. For AC input, it's recommended to use a CR constant with 0.1 to 47 F + 47 to 120 (1/2W). Another cause might be a limit switch with a neon lamp, in which case you can apply the same resistor solution or create an independent display circuit. Finally, leakage current from the wiring cable's line capacity could be the issue. The same resistor fix applies here, but note that leakage current isn't generated when the power supply is located on the input equipment side.
M
meyerryanAug 27, 2025
Why is the ERR LED on or flashing on my Mitsubishi Controller?
- E
  Eric VillaAug 27, 2025
  The ERR LED on your Mitsubishi Controller may be lit or flashing because: - An error is being generated. Confirm the error code and take corrective action described in Section 8.1. - Intelligent function module setting switch 5 is set to "other than 0". Using GX Developer parameter setting, set intelligent function module setting switch 5 to "0".
E
Elizabeth JohnsonAug 27, 2025
Why is the RUN LED flashing or off on my Mitsubishi Controller?
- M
  Mark ChristensenAug 27, 2025
  The RUN LED might be flashing or turned off if the mode is set to the offset/gain setting mode. Reset switch 4 of the intelligent function module switch setting for GX Developer to the normal mode.
K
Kristen HernandezAug 28, 2025
Why is the analog value not within the reference accuracy of the theoretical value on my Mitsubishi MELSEC Q?
- K
  Kelly FisherAug 28, 2025
  If you're using voltage output and observe a small load resistance of the connected external device and a long wiring distance, a voltage drop due to the wiring impedance and load current may be large, and the voltage applied to the external device is low. In this case, the factory default range setting may not satisfy the reference accuracy. Use User range setting and adjust the offset and gain values after wiring.
G
gonzaleztroyAug 28, 2025
What should I do if the analog output value is not “HOLD” on my Mitsubishi MELSEC Q Controller?
- N
  nicholaspageAug 28, 2025
  If the analog output value is not in “HOLD” mode, check the Switch 3 setting of the intelligent function module switch setting on GX Developer. Also, if the Q66DA-G is used on a MELSECNET/H remote I/O station, take action, referring to POINT (2) in Section 3.2.1.
R
Robert GuzmanAug 29, 2025
What to do if an invalid value is set in the offset/gain setting on Mitsubishi MELSEC Q?
- M
  Melinda FisherAug 29, 2025
  Perform the offset/gain setting again for the error channel. If the error occurs again, the module may be malfunctioning. Please consult your local Mitsubishi representative, explaining a detailed description of the problem.
M
Melissa BakerAug 29, 2025
How to fix offset value equal to or larger than gain value on Mitsubishi MELSEC Q?
- M
  Mark KennedyAug 30, 2025
  Reset the Mitsubishi Controller so that the offset value is smaller than the gain value.
D
Daniel WaltonAug 25, 2025
What to do if the fuse broken detection occurs in Mitsubishi MELSEC Q?
- J
  Jean ChandlerAug 25, 2025
  If the fuse for the coincidence signal external output section has blown in your Mitsubishi Controller, it must be replaced by a qualified technician from the Service Center. Contact your branch office or distributor with a detailed description of the issue.
K
Kyle AguirreAug 31, 2025
How to correct warning output lower limit value equal to or greater than the warning output upper limit value on Mitsubishi MELSEC Q Controller?
- B
  Briana ClarkAug 31, 2025
  Make setting so that the warning output upper limit value is greater than the warning output lower limit value.
E
Edward MorrisAug 31, 2025
What to do if there is an invalid value in offset/gain setting and the error channel number cannot be identified on Mitsubishi Controller?
- J
  jason66Aug 31, 2025
  Perform the offset/gain setting again for all of the channels that use the user range settings. If the error occurs again, the module may be malfunctioning. Please consult your local Mitsubishi representative, explaining a detailed description of the problem.

Mitsubishi MELSEC Q Series Specifications

General

Series	MELSEC Q Series
Type	Modular PLC
Programming Software	GX Works2, GX Works3
Category	Programmable Logic Controller (PLC)
I/O Modules	Digital I/O, Analog I/O, High-Speed Counter, Positioning
Communication	Ethernet, CC-Link
Programming Languages	Ladder Logic, Structured Text, Function Block Diagram, Sequential Function Chart, Instruction List
Memory	Flash Memory
I/O Points	Up to 4096 points (expandable with additional modules)
Power Supply	AC or DC power supply options available, depending on the base unit and modules.
Mounting	DIN rail mounting
Operating Temperature	0°C to 55°C
Storage Temperature	-25°C to 75°C
Humidity	5% to 95% (non-condensing)
Vibration Resistance	10 to 57 Hz, 0.075mm amplitude
Weight	Varies depending on the module, from a few grams to several kilograms.
Shock Resistance	147 m/s² (3 times each in X, Y, Z directions)

Related product manuals

Preview: Mitsubishi MELSEC System Q

Mitsubishi MELSEC System Q

Preview: Mitsubishi MELSEC-Q/L

Mitsubishi MELSEC-Q/L

Mitsubishi Melsec-Q QD75P1

Preview: Mitsubishi MELSEC

Mitsubishi MELSEC

Preview: Mitsubishi MELSEC QCPU

Mitsubishi MELSEC QCPU

Mitsubishi MELSEC AC10TB

Mitsubishi MELSEC A1SY10

Mitsubishi MELSEC A1S62P

Mitsubishi MELSEC AC30TB

Mitsubishi MELSEC A1SY22

Mitsubishi MELSEC A1SY42

Mitsubishi MELSEC F2-40MR