To Next PageTo Next PageWhat does encoder initial communication error 2 mean on Mitsubishi MR-J4-10A?
Encoder initial communication error 2 on your Mitsubishi Amplifier can indicate an encoder malfunction or a load-side encoder malfunction.
What causes encoder initial communication error 1 on Mitsubishi Amplifier?
Encoder initial communication error 1 on your Mitsubishi Amplifier can be caused by: * Encoder initial communication - Receive data error 1. * Encoder initial communication - Receive data error 2. * Encoder initial communication - Receive data error 3. * Encoder initial communication - Transmission data error 1. * Encoder initial communication - Transmission data error 2. * Encoder initial communication - Transmission data error 3. * Encoder initial communication - Process error 1. * Encoder initial communication - Process error 2. * Encoder initial communication - Process error 3. * Encoder initial communication - Process error 4. * Encoder initial communication - Process error 5. * Encoder initial communication - Process error 6.
Why does my Mitsubishi MR-J4-10A Amplifier show an overvoltage error?
An overvoltage error in your Mitsubishi Amplifier is due to a main circuit voltage error.
What does memory error 2 mean on Mitsubishi Amplifier?
Memory error 2 (EEP-ROM) on your Mitsubishi Amplifier can occur due to: * EEP-ROM error at power on. * EEP-ROM error during operation.
What causes encoder normal communication error 1 on Mitsubishi MR-J4-10A?
Encoder normal communication error 1 on your Mitsubishi Amplifier can be caused by: * Encoder normal communication - Receive data error 1. * Encoder normal communication - Receive data error 2. * Encoder normal communication - Receive data error 3. * Encoder normal communication - Transmission data error 1. * Encoder normal communication - Transmission data error 2. * Encoder normal communication - Transmission data error 3. * Encoder normal communication - Receive data error 4. * Encoder normal communication - Receive data error 5.
What does encoder normal communication error 2 mean on Mitsubishi MR-J4-10A?
Encoder normal communication error 2 on your Mitsubishi Amplifier can be caused by: * Encoder data error 1. * Encoder data update error. * Encoder data waveform error. * Encoder non-signal error. * Encoder hardware error 1. * Encoder hardware error 2. * Encoder data error 2.
What causes a servo control error on my Mitsubishi MR-J4-10A Amplifier?
A servo control error on your Mitsubishi Amplifier (specifically for linear servo motors and direct drive motors) can be caused by: * Servo control error by position deviation. * Servo control error by speed deviation. * Servo control error by torque/thrust deviation. * Fully closed loop control error by position deviation. * Fully closed loop control error by speed deviation. * Fully closed loop control error by position deviation during command stop.
What does a board error on my Mitsubishi MR-J4-10A mean?
A board error on your Mitsubishi Amplifier indicates: * Board error 1. * Board error 2. * Board error 3.
What causes a regenerative error in my Mitsubishi MR-J4-10A Amplifier?
A regenerative error in your Mitsubishi Amplifier can stem from: * Regeneration heat error. * Regeneration signal error. * Regeneration feedback signal error.
What does parameter error mean on my Mitsubishi MR-J4-10A?
A parameter error on your Mitsubishi Amplifier indicates either a parameter setting range error or a parameter combination error.
General| Series | MR-J4 |
|---|---|
| Type | AC Servo Amplifier |
| Model | MR-J4-10A |
| Voltage Class | 200V |
| Position Control | Yes |
| Speed Control | Yes |
| Torque Control | Yes |
| Full-closed control | Yes |
| Communication | SSCNET III/H |
| Dynamic brake | Built-in |
| Ambient temperature | 0 to 55 °C |
| Vibration resistance | 5.9 m/s² |
| Rated output current | 0.6 A |
| Cooling Method | Natural Cooling |
| Rated Output | 0.1 kW |
| Input Voltage | 200V |
| Output Voltage | 200V |
| Control Mode | Position control, Speed control, Torque control |
| Protection Functions | Overvoltage, Undervoltage |
| Control Method | Sine wave PWM control |
| Ambient humidity | Up to 90% (No condensation) |
