Chapter 2 Part B
2.OL and 2.4L four-cylinder engines
Contents
Camshaft - removal, inspection and installation .............. 10
Crankshaft front oil seal - replacement ..................... 9
Cylinder compression check ................... See Chapter 2D
Cylinder head - removal and installation .................... 13
Drivebelt check, adjustment and replacement ....... See Chapter 1
Engine mounts-check and replacement ................... 18
Engine oil
and
oil filter change ................... See Chapter 1
Engine overhaul -general information ........... See Chapter 2D
Engine - removal and installation ............... See Chapter 2D
Exhaust manifold - removal and installation ................. 12
Flywheel/driveplate - removal and installation ............... 16
General information and engine identification ................ 1
Hydraulic lash adjusters-removal, inspection and installation ... 7
Intake manifold - removal and installation ................... 11
Oil pan - removal and installation ......................... 14
Oil pump - removal, inspection and installation ............... I5
Rear main oil seal - replacement .......................... 17
Repair operations possible with the engine in the vehicle ....... 2
Rocker arm assembly - removal, inspection and installation ..... 5
Spark plug replacement .....................
_
.. See Chapter 1
Timing belt, Silent Shaft belt and sprockets - removal,
inspection and installation ............................. 8
Top Dead Center (TDC) for number one piston - locating ..... 3
Valve cover - removal and installation ...................... 4
Valves - servicing ............................ See Chapter 2D
Valve springs, retainers and seals - replacement ............. 6
Water pump - removal and installation ............ See Chapter 3
Specifications
General
Firingorder.. .........................................
Cylinder numbers (drivebelt end-to-transmission end) .........
Displacement
2.OL ................................. . ............
2.4L ..............................................
Bore
2.OL ........... ..& ..............................
2.4L ........... ..$? ...............................
Stroke
2.OL
..
..-...._.._..._.....= .......................
2.4L ..............................................
Camshaft
Camshaftendplay ................... ..-. ...............
Lobe height (standard)
2.OL (1983and 1984) ..............................
,
...
2.OL(1985) ................................... . .....
2.OL(1986on) .......................................
2.4L ..............................................
Wearlimit ............................................
Camshaft bearing oil clearance ...........................
Cylinder head
Warpagelimit .........................................
Timing belt
Timing belt deflection ...................................
Clearance between timing belt and seal line .................
Oil pump
Clearances
Tip clearance
Drive gear ................ r. ......................
Driven gear ......................................
Side clearance
Drivegear .......................................
Drivengear ......................................
Pressure relief spring
Freelength .........................................
Load ..............................................
Torque specifications
Valvecoverbolts
.................
. ....................
Intake/exhaust manifold nuts/bolts .........................
Camshaft sprocket bolt ...................
_
.. ._ .........
l-3-4-2
1-2-3-4
121.9 cubic inches
143.4 cubic inches
3.35 inches
3.41 inches
3.46 inches
3.94 inches
0.0’04 to 0.008 in
1.661 inch
1.657 inch
1.6565 inch
1.6693 inch
0.020 inch
0.002 to 0.0035 inch
0.002 inch
Tension automatically adjusted
Approx. 9/l B-inch
.
.
0.0063 to 0.0083 inch
0.0051 to 0.0071 inch
0.0031 to 0.0055 inch
0.0024 to 0.0047 inch
1.834 inch
13.4 lb @ 1.579 inch
Ft-lbs (unless otherwise indicated)
48 to 60 in-lbs
132 to 168 in-lbs
58 to 72
To Next Page
Loading...
