Mitsubishi Q64AD-GH User Manual

A - 9 A - 9
3.4.4 CH
A/D conversion starting time setting
(buffer memory addresses 5, 6: Un\G5, Un\G6) (Q62AD-DGH only) ............................................ 3-52
3.4.5 Averaging process specification (buffer memory address 9: Un\G9) ............................................. 3-54
3.4.6 A/D conversion completed flag (buffer memory address 10: Un\G10) .......................................... 3-55
3.4.7 CH
digital output value (16bit) (buffer memory addresses 11 to 14: Un\G11 to Un\G14) .......... 3-56
3.4.8 Write data error codes (buffer memory address 19: Un\G19) ........................................................ 3-56
3.4.9 Setting range (buffer memory address 20: Un\G20) ....................................................................... 3-57
3.4.10 Offset/gain setting mode (buffer memory addresses 22, 23: Un\G22, Un\G23) ......................... 3-58
3.4.11 CH
maximum value/minimum value storage area (16bit)
(buffer memory addresses 30 to 37: Un\G30 to Un\G37) ............................................................ 3-58
3.4.12 Input signal error detection extended/input signal error detection/warning output settings (buffer
memory address 47: Un\G47) ....................................................................................................... 3-59
3.4.13 Warning output flag (buffer memory address 48 :Un\G48) .......................................................... 3-60
3.4.14 Input signal error detection flag (buffer memory address 49: Un\G49) ........................................ 3-61
3.4.15 CH
digital output value (32bit) (buffer memory addresses 54 to 61: Un\G54 to Un\G61) ........ 3-61
3.4.16 CH
maximum value/minimum value storage area (32bit)
(buffer memory addresses 62 to 77: Un\G62 to Un\G77) ............................................................ 3-62
3.4.17 CH
process alarm upper/lower limit value
(buffer memory addresses 86 to 117: Un\G86 to Un\G117) ........................................................ 3-62
3.4.18 CH
rate alarm warning detection period
(buffer memory addresses 118 to 121: Un\G118 to Un\G121) .................................................... 3-63
3.4.19 CH
rate alarm upper/lower limit value
(buffer memory addresses 122 to 137: Un\G122 to Un\G137) .................................................... 3-64
3.4.20 CH
input signal error detection setting value/CH input signal error detection lower limit
setting value (buffer memory addresses 138 to 141: Un\G138 to Un\G141)
CH
input signal error detection setting upper value
(buffer memory addresses 142 to 145: Un\G142 to Un\G145) .................................................... 3-65
3.4.21 Mode switching setting (buffer memory addresses 158, 159: Un\G158, Un\G159) .................... 3-67
3.4.22 Pass data classification setting (buffer memory addresses 200: Un\G200) (Q64AD-GH only) .. 3-67
3.4.23 Industrial shipment settings and user range settings offset/gain value
(buffer memory addresses 202 to 233: Un\G202 to Un\G233) .................................................... 3-68
4 SETUP AND PROCEDURES BEFORE OPERATION 4- 1 to 4-21
4.1 Handling Precautions .............................................................................................................................. 4- 1
4.2 Setup and Procedures before Operation ............................................................................................... 4- 2
4.3 Part Identification Nomenclature ............................................................................................................ 4- 3
4.4 Wiring ....................................................................................................................................................... 4- 5
4.4.1 Wiring precautions............................................................................................................................ 4- 5
4.4.2 External wiring .................................................................................................................................. 4- 6
4.5 Switch Setting for Intelligent Function Module ....................................................................................... 4- 9
4.6 Offset/Gain Settings ................................................................................................................................ 4-11
4.6.1 Offset/gain settings (Q64AD-GH) .................................................................................................... 4-11
4.6.2 Offset/gain settings (Q62AD-DGH) ................................................................................................. 4-16
4.6.3 A/D conversion value storage during offset/gain setting ................................................................ 4-21
5 UTILITY PACKAGE (GX Configurator-AD) 5- 1 to 5-32
5.1 Utility Package Functions........................................................................................................................ 5- 1

Mitsubishi Q64AD-GH Specifications

General

Brand	Mitsubishi
Model	Q64AD-GH
Category	Controller
Language	English