MMM Group incucell v 111 - User Manual

Instructions for use
Laboratory drying ovens and incubators
line Comfort
LSI_K_np_en 1206_mmm_V2.08_B2V
ECOCELL 22, 55, 111, 222, 404, 707
DUROCELL 22, 55, 111, 222
VENTICELL 22, 55, 111, 222, 222/2, 404,
404/2, 707, 707/2
INCUCELL 22, 55, 111, 222, 404, 707
INCUCELL V 22, 55, 111, 222, 404, 707
ECOCELL 22, 55, 111, 222, 404, 707
DUROCELL 22, 55, 111, 222
VENTICELL 22, 55, 111, 222, 404, 707
INCUCELL 22, 55, 111, 222, 404, 707
INCUCELL V 22, 55, 111, 222, 404, 707
Návod na servis
Laboratorní sušárny a inkubátory - linie
Standard
LSI-S_ns_cz_0801_V2.01_B2V
Návod k použití
Laboratorní sušárny a inkubátory
linie Komfort
LSI_K_np_cz 0608_V1.14
ECOCELL 22, 55, 111, 222, 404, 707
DUROCELL 22, 55, 111, 222
VENTICELL 22, 55, 111, 222, 404, 707
STERICELL 22, 55, 111, 222, 404
INCUCELL 22, 55, 111, 222, 404, 707
INCUCELL V 22, 55, 111, 222, 404, 707

Summary

Important Instructions for Use

Unpacking, Checking, and Transport

Pre-Installation Requirements

Provides essential steps and conditions for setting up the oven before operation, including environmental requirements.

Power Connection and Control Panel

Power Connection and Connectors

Details how to connect the oven to power and describes the available connectors and their pinouts.

Control Panel Layout and Functions

Explains the functions of the buttons and indicators on the oven's control panel.

Function and Operating Procedures

Basic Unit Settings and Service Mode

Covers initial configuration and fundamental settings required to operate the oven, including service mode access.

Safety Thermostat Configuration

Explains how to set the safety thermostat to prevent overheating and protect the unit and samples.

Temperature Tolerance and Error Handling

Allows adjustment of temperature tolerance limits and defines error handling for deviations.

Door Blocking Functionality

Details the door blocking mechanism to prevent accidental opening.

Program P1: Constant Temperature Operation

Setting Program P1

Step-by-step guide to configure Program P1, including temperature settings.

Starting and Stopping Program P1

Viewing P1 Parameters During Run

Program P2: Temperature and Time Control

Setting Program P2

Step-by-step guide to configure Program P2, including temperature and time settings.

Starting and Stopping Program P2

Program P3: Delayed Start Operation

Setting Program P3

Step-by-step guide to configure Program P3, including delay and temperature settings.

Starting and Stopping Program P3

Viewing P3 Parameters During Run

Program P4: Temperature Levels and Cycling

Setting Program P4

Guide to configure Program P4, including temperature levels and dwell times.

Setting Segment T1 for P4

Setting Segment T2 for P4

Starting and Stopping Program P4

Viewing P4 Parameters During Run

Program P5: Multi-Segment Profiles

Description and Control of Program P5

Explains the structure and control of Program P5, which uses up to 40 segments.

Program P6: Time-Based Scheduling

Description of Program P6

Explains the unique time-based scheduling mechanism of Program P6.

Program P6 Setting Procedure

Guides on how to set up Program P6 using specific date and time parameters.

Starting and Handling P6 Power Failures

Examples of Program P6 Settings

Operational Features and Troubleshooting

Keyboard Blocking Function

Error Messages and Troubleshooting

Lists and explains common error codes and their meanings for troubleshooting.

Air Flap Adjustment and Function

Unit Technical Parameters

Electric Connection Details

Details the electrical requirements, connections, and safety standards for installing the unit.

Cleaning and Decontamination

Unit Cleaning and Decontamination Procedures

Provides instructions on how to clean and decontaminate the oven safely and effectively.

Maintenance and Service

Electrical Component Inspection

General Maintenance Operations

Warranty and Support

Warranty Terms and Service Conditions

Door Blocking and Program Protection

Door Blocking Functionality Details

Details the door blocking mechanism to prevent accidental opening.

Programme Setting Protection via Chip Card

Installation Data for Pass-Through Models

Venticell 222;2 Installation Data

Venticell 404;2 Installation Data

Venticell 707;2 Installation Data

Specialized Functions and Sterilization

Preventing Cultivating Media Drying

Incucell Decontaminating Function

Details the decontamination function for Incucell models to prevent chamber contamination.

Venticell Sterilization Function

Introduces sterilization programs (SS and SP) for Venticell models.

Sterilization Program SS Details

Basic Sterilization Program SS

Explains the basic sterilization program (SS) for Venticell units.

Setting Program SS

Step-by-step guide to configure the SS sterilization program parameters.

Starting Program SS

Viewing SS Parameters During Run

Stopping Program SS

Sterilization Program SP Details

Sterilization Program SP with Preheating

Explains the SP sterilization program with a preheating phase for even temperature distribution.

Setting Program SP

Guide to configure the SP sterilization program with preheating.

Setting Segment T1 for SP

Setting Segment T2 for SP

Starting Program SP

Viewing SP Parameters During Run

Stopping Program SP

SS;SP Programs with Two-Door Blocking

Emergency Door Opening

MMM Group incucell v 111 Specifications

General

Category	Laboratory Equipment
Type	Incubator
Volume	111 liters
Power Consumption	300 W
Power Supply	230V, 50/60Hz