MMM Group venticell 22 - User Manual

Instructions for use
Laboratory drying ovens and incubators
line Comfort
LSI_K_np_en 1206_mmm_V2.08_B2V
ECOCELL 22, 55, 111, 222, 404, 707
DUROCELL 22, 55, 111, 222
VENTICELL 22, 55, 111, 222, 222/2, 404,
404/2, 707, 707/2
INCUCELL 22, 55, 111, 222, 404, 707
INCUCELL V 22, 55, 111, 222, 404, 707
ECOCELL 22, 55, 111, 222, 404, 707
DUROCELL 22, 55, 111, 222
VENTICELL 22, 55, 111, 222, 404, 707
INCUCELL 22, 55, 111, 222, 404, 707
INCUCELL V 22, 55, 111, 222, 404, 707
Návod na servis
Laboratorní sušárny a inkubátory - linie
Standard
LSI-S_ns_cz_0801_V2.01_B2V
Návod k použití
Laboratorní sušárny a inkubátory
linie Komfort
LSI_K_np_cz 0608_V1.14
ECOCELL 22, 55, 111, 222, 404, 707
DUROCELL 22, 55, 111, 222
VENTICELL 22, 55, 111, 222, 404, 707
STERICELL 22, 55, 111, 222, 404
INCUCELL 22, 55, 111, 222, 404, 707
INCUCELL V 22, 55, 111, 222, 404, 707

Summary

1 GENERAL

2 IMPORTANT INSTRUCTIONS

2.1 UNPACKING, CHECKING AND TRANSPORT

Details how to unpack, inspect for damage, and handle the oven during transport and unpacking.

2.2 PRE INSTALLATION

Provides guidelines for oven installation, including environmental conditions, power connection, and initial operation.

3 DESCRIPTION OF THE OVEN

4 FUNCTION AND OPERATING

4.1 BASIC SETTING OF THE UNITS

Covers fundamental input requirements and service modes for operating the Comfort regulator units.

4.2 PROGRAM P1

Explains setting and operating Program P1 for constant temperature until unit switch-off.

4.3 PROGRAM P2

Details setup and operation of Program P2 for maintaining a set temperature for a defined time.

4.4 PROGRAM P3

Describes Program P3, featuring a delayed start function before set temperature operation.

4.5 PROGRAM P4

Explains Program P4 with two temperature levels, controlled speed, and cycling.

4.6 PROGRAM P5

Describes Program P5, composed of segments determined by real time and calendar date.

4.7 PROGRAM P6

Details Program P6, using segments determined by real time and calendar date for scheduling.

4.10 ERROR MESSAGES

Lists and explains various error messages displayed by the unit, with corresponding troubleshooting steps.

4.11 PRINTING THE PROTOCOL

Details connecting the printer, setting intervals, and printing protocols from the unit.

4.13 EXCHANGING THE DOOR SEALING AND ADJUSTING THE DOOR

Provides instructions on how to exchange door sealing and adjust the door for proper fit and seal.

5 PARAMETERS OF THE UNIT

5.1 ELECTRIC CONNECTIONS

Provides data and requirements for connecting the unit to electrical mains, including voltage and current.

6 CLEANING AND DECONTAMINATION OF THE UNIT

7 MAINTENANCE

8 WARRANTY AND SERVICE

9 TRANSPORT AND STORAGE

11 OPTIONAL EQUIPMENT

11.10 DEVICES WITH THE DOOR BLOCKING FUNCTION

11.15 IC AND ICV WITH DECONTAMINATING FUNCTION

11.16 VENTICELL WITH STERILIZATION FUNCTION

11.16.1 BASIC STERILIZATION PROGRAMME SS

11.16.1.1 SS PROGRAMME SETTING

11.16.1.6 STERILIZATION PROGRAMME SETTING AND COURSE

11.16.2 STERILIZATION PROGRAMME SP WITH PREHEATING PHASE

11.16.2.1 SP PROGRAMME SETTING

12 EMERGENCY DOOR OPENING

4.11 PRINTING THE PROTOCOL

Printer Connection and Operation

4.13 EXCHANGING THE DOOR SEALING AND ADJUSTING THE DOOR

EC-DECLARATION OF CONFORMITY

MMM Group venticell 22 Specifications

General

Brand	MMM Group
Model	venticell 22
Category	Laboratory Equipment
Language	English