To Next PageTo Next PageWhat to do if batteries are dead in Moen MOTIONSENSE WAVE 7864EWBL Plumbing Product?
To resolve dead batteries in the battery holder of your Moen Plumbing Product, unplug the battery holder cable and replace the batteries with new AA alkaline batteries.
How to plug in power cable in Moen Plumbing Product?
Ensure the power cable is fully plugged into the control box of your Moen Plumbing Product by firmly pushing the power cable into the control box.
Why is the light blinking on my Moen MOTIONSENSE WAVE 7864EWBL Plumbing Product?
If the light on your Moen Plumbing Product is blinking, this could be due to low battery voltage, dead batteries, or the use of rechargeable batteries. Replace the batteries with new AA alkaline batteries to ensure proper faucet functionality.
What to do if water does not flow and light is on for Moen MOTIONSENSE WAVE 7864EWBL?
If water is not flowing from your Moen Plumbing Product and the light is on, the water supplies may not be turned on. Turn on the water supplies to resolve this issue.
Why does the water keep flowing and not turn off in my Moen MOTIONSENSE WAVE 7864EWBL?
If water keeps flowing from your Moen Plumbing Product and does not turn off, ensure that the handle is not in the open position and close it fully. Also, check if the battery holder cable became unplugged while the faucet was running, and if so, unplug the battery holder cable fully.
How to fix low water flow in Moen MOTIONSENSE WAVE 7864EWBL Plumbing Product?
If you're experiencing low water flow (hot, cold, or both) from your Moen Plumbing Product, or only hot or cold water flows, the water supplies may not be fully turned on. Ensure that all water supplies are turned on. Also, check for pinched or kinked hoses and make sure they are not obstructed. Lastly, the filters might be clogged, so cleaning both filters is recommended.
Why is the sensor not functioning on my Moen MOTIONSENSE WAVE 7864EWBL?
If the sensor on your Moen Plumbing Product is not functioning, it could be deactivated. Reactivate the sensor. Also, ensure that the handle is fully closed, as a slightly open handle can interfere with sensor operation. Finally, make sure there are no objects within 8 inches of the sensor, as this can also cause it to malfunction.
How to fix reversed hot and cold water flow on Moen MOTIONSENSE WAVE 7864EWBL Plumbing Product?
If the handle position for hot and cold water flow is reversed on your Moen Plumbing Product (cold forward), the hot and cold hoses may be installed in reversed order. If the hoses are reversed at the wall stops, turn off the supplies and connect the hot supply hose to the hot stop and the cold supply hose to the cold stop. If the hoses are reversed at the control box, turn off the supplies and connect the hot supply hose to the hot side of the control box and the cold supply hose to the cold side of the control box.
What happens if the wall switch is OFF when using AC adapter with power splitter for Moen MOTIONSENSE WAVE 7864EWBL Plumbing Product?
If you are using an AC adapter with a power splitter and the wall switch for the power outlet is off, the faucet will function normally until battery power is depleted. Turn the wall switch on to ensure power at the outlet. If the wall switch remains off, the faucet will continue to function normally until the battery power is depleted.
What to do if wall switch is OFF when using AC adapter for Moen MOTIONSENSE WAVE 7864EWBL Plumbing Product?
If you are using an AC adapter only and the wall switch for the power outlet is off, turn the wall switch on to ensure power at the outlet. Clear the area for proper startup.
General| Installation Type | Deck Mount |
|---|---|
| Handle Type | Lever |
| Flow Rate | 1.5 GPM |
| Warranty | Limited Lifetime |
| Valve Type | Ceramic Disc |
| Supply Lines Included | Yes |
| Motion Sensor | Yes |
| Material | Metal |
| ADA Compliant | Yes |
| Number of Handles | 1 |
| Product Type | Faucet |
| Finish | Black |
| Collection | Moen Motionsense |
Provides contact information for installation help, missing or replacement parts.
Lists tools recommended for safe and easy faucet replacement.
Guides users on how to register their Moen product online for warranty and support.
Ensures adequate space for control box installation before removing the existing faucet.
Advises turning off water supply and relieving pressure before disassembling the valve.
Illustrates the typical installation setup for the faucet.
Details an alternative setup with the control box positioned on the left side.
Shows an alternative setup with the soap dispenser on the left side.
Describes how to mount the control box on a wall using a specific kit.
Checks for sufficient space to install the control box beneath the sink.
Information on acquiring the optional kit for wall-mounting the control box.
Installs the faucet body and data cable into a single sink opening.
Installs the faucet body using a deck plate for three sink openings.
Attaches the mounting washer and nut to the faucet body, ensuring the data cable is clear.
Uses the provided installation tool to securely tighten the mounting nut.
Threads the hose guide nut onto the faucet body's mounting shank.
Feeds the smaller end of the pulldown hose through the faucet spout and body.
Connects the spray wand to the pulldown hose, ensuring the hose nut is flush.
Connects the pulldown hose to the quick-connect port on the control box.
Inserts the data cable into the designated port at the bottom of the control box.
Attaches the control box to the hose guide nut or an alternative side mount.
Connects the hot and cold water supply hoses to the appropriate valves.
Locates the hose weight mark and installs the weight on the pulldown hose.
Chooses a mounting spot for the battery holder, checking wire reach to the control box.
Inserts six AA batteries into the holder, ensuring proper orientation.
Secures the battery holder to the wall using fasteners or provided screws.
Activates the water supply to the faucet.
Plugs the battery holder's cable into the control box power port.
Directs users to the Quick Start Guide for essential start-up procedures.
Uses zip ties to manage hoses and cables, ensuring free movement of the pulldown hose.
Checks that the faucet handle correctly controls hot and cold water flow.
Tests the motion sensor to ensure it activates and deactivates water flow properly.
Explains the different spray patterns available via the spray wand button.
Details the process of turning the motion sensor on or off using handle manipulations.
Provides a secondary method for enabling the sensor by cycling power.
Guides through installing the soap dispenser base, pump, and bottle.
Explains how to clean filters to resolve problems with reduced water flow.
Provides detailed steps for cleaning and reinstalling filter screens to improve flow.
Connects water supply lines and performs a flow test to ensure proper operation.
Instructs on cleaning the spray wand's internal screen and O-ring to fix irregular flow.
Diagnoses and resolves problems related to water not flowing and indicator light status.
Addresses issues where the sensor is inactive or the handle controls are reversed.
Troubleshoots water that won't turn off and causes for the indicator light blinking.
States compliance with FCC regulations for digital devices and provides interference correction tips.
Explains the terms, coverage, and limitations of the MotionSense Wave™™ system warranty.
