INSTALLATION WIRING
DIAGRAM
I20
VAC
60
HZ
I
A
MAX
(SUPERVISED)
PRINTLO
CIRCUIT
BOAR~
TB1
I
(GREEN)
AC PILOT
SUPERVISORY
(RED)
ALARM
(WHITE)
TROUBLE
CABINET
WOR
1
MODEL
C-100A-24
FIRE
ALARM CONTROL
::
::
I
(RED1
(YELWW)
TROUBLE
HmwL
8NoMAL
Noma
%p
I
I
I
SILENCE
SILENCE
RESET
TEST
I
I
-
+
nLARM
MODE
POLARITY
I
-b
-
SUPERvlSORV
MCDE
POLARITY
I
+OOOI~MS
BATIZRY
REMOTE
TROUBLE
wA"
24V
TROUBLE
BELL
nux
3-IS AMPS
24
VDC 24VDC
ALARM
pdR
.2S(;,"TAX.
25
AMAX.
(HOT
WEN
z:42i&
TONOTE
SWERVISEDI SUPERVISED)
(SUPERVISED)
l2
(DOES
IS
USE0
.3
A
MU.
CIRCUIT
&%rq
12
SOHMS
l
2
R
MAX.
ON
CONDumRS
FOR
SMOKE
I.E.
zs
m
28
&
26
m 27
(S00'NO.
IIAWCI
SUITABLE
FOR
AT
24
VDC
CONNECTION
7'0
REFER
TO
NOTE
DEVICE INDICATED
IN
10
NOTE
I
NOTES:
(SUPERVISED) (SUPERVISED
LIMITED
ENERGY
CIRCUIT)
Wire
in
accordance with NFPA Installation Standards 72A and 728, and all applicable national, state, and local electricai codes.
Indicated circuit capacities may be exceeded provided total external current drain does not exceed 2.85 amps.
Remove resistor from terminals
11
and 12 when connecting an external device or municipal box circuit. Connect any 43 ohm 250
ma trip coil in series with 43 ohm
5
watt resistor and connect direct. Maximum recommended supe~sory current is 10 ma. If shunt
connection
is
used, the shunt connection is recognized as a supplementary signaling unit as part of local control unit only. This type
connection is not recommended as an auxiliary control unit connection per NFPA Number 72B.
Automatic detectors, manual alarm stations and smoke detectors may be used with the C-100A but must be U.
L.
listed. The C-100A
is
also suitable for connection of waterflow alarm devices when an audible device is connected to terminals 11 and 12.
Only circuits co~ected to terminals 25 through 28 are limited energy circuits.
The system
is
actuated manually or automatically through the C-100A control to sounding devices and auxiliary circuits.
The signal circuit is supervised noncoded type.
?he C-100A may
be
used for local andlor auxiliary systems. When used for auxiliary systems, only rechargeable standby power system
with 60 hours capacity (NFPA 72B) may be used.
U. L. listed polarized alarm bells must be used to block the bell circuit supervisory current.
Use
IN4003 (200 volt, 1 amp) diode as end of tine device on supenriled alarm bell circuit.
24 VDC smoke detectors must have
a
minimum voltage rating of 28 VDC. End of loop detectors not having internal power super-
vision must have external power supervisory module connected to the loop.
Use two Eveready 1463 batteries or equal connected in series. Test batteries by disconnecting AC power and placing control in alarm.
Battery voltage below 20 V measured during the test indicates batteries should be replaced.
For control operation instructions. refer to label
243-045-00.
Supe~sed power supply connections when using smoke detectors are included in I-O-M Manual, Section 11.
The C-100A-24 is intended for the following type and sewice:
TYPE:
SERVICE:
(L): Local system type.
(A):
Automatic fie alarm: Thermostats, smoke detectors, etc.
(A): Auxiliary system type. (M): Manual fire alarm: Nhnually operated boxes.
LABEL
PIN
243-040-00
F7935
REV
D
MONACO
ENTERPRISES.
INC.
SPOKANE.
WA
99214
To Next Page
Loading...