What to do if Motic Microscope lamp does not light?
If the lamp in your Motic Microscope does not light, first ensure that the power supply is plugged in. If it is, check if the lamp is properly installed. If the lamp is installed correctly and still doesn't light, the lamp may be burnt out and needs to be replaced.
Why is there vignetting or uneven brightness in my Motic BA310 Pol Microscope?
Vignetting or uneven brightness can occur in your Motic Microscope due to several reasons. It may be that the analyser slider is in an intermediate position, so adjust it to the correct position. Another cause can be the compensator slider being midway, so adjust that as well. If the Bertrand lens is in the optical path, remove it. Ensure the condenser is correctly mounted and centered, and that its height is properly adjusted. Also, make sure the condenser top lens is fully swung in or out. Check that the field and aperture diaphragms aren't closed too far, and that you're using the proper condenser objective combination. Finally, ensure the revolving nosepiece is clicked into position and the trinocular eyepiece tube optical path selector lever is correctly adjusted.
What to do if my Motic Microscope image is poor (low contrast or resolution)?
A poor image with low contrast or resolution in your Motic Microscope can be caused by several factors. Ensure the condenser height is properly adjusted and the aperture diaphragm is not closed too far. Using a cover glass of proper thickness is essential; if one isn't used, add one. If using immersion oil, ensure no air bubbles are present and that you're using the specified type. Also, make sure immersion oil isn't on a dry objective. Clean any greasy residue from the eye lens. Adjust the illumination settings. Finally, make sure the specimen holder is securely fixed on the stage and the specimen is secured in position.
How to fix dust or dirt in the field of view of my Motic BA310 Pol Microscope?
If you notice dust or dirt in the field of view of your Motic Microscope, it could be due to several reasons. Make sure that the aperture diaphragm is not closed too far and that the condenser height is properly adjusted. Check the specimen surface for dust or dirt and clean if necessary. Additionally, inspect and clean the field lens, filter, condenser, or eyepiece for any dust or dirt accumulation.
Why is my Motic BA310 Pol lamp flickering?
If the lamp in your Motic Microscope is flickering, check if the connectors are securely connected. It's also possible that the lamp is nearing the end of its service life and needs replacement. Ensure the lamp is securely plugged into the socket.
Why does Motic BA310 Pol Microscope lamp blow out immediately?
If the lamp in your Motic Microscope blows out immediately after being turned on, it is likely that the specified lamp is not being used. Make sure to use the correct lamp type.
What to do if Motic BA310 Pol objectives strike the specimen?
If, when switching from low to high magnification on your Motic Microscope, the high magnification objectives strike the specimen, ensure that the slide is right-side up and that the cover glass is not too thick. You may need to replace it with a thinner cover glass. Also, adjust the eyepiece diopter.
Why does Motic BA310 Pol Microscope lamp flicker?
If the lamp in your Motic Microscope flickers, check that all connectors are securely connected. If the flickering persists, the lamp may be nearing the end of its service life and require replacement. Also, ensure the lamp is securely plugged into the socket.
What to do if Motic Microscope lamp blows out immediately?
If the lamp in your Motic Microscope blows out immediately, it is likely that the specified lamp is not being used. Ensure you are using the correct lamp type.
How to resolve no cohesion of binocular image in Motic Microscope?
If you're experiencing no cohesion of the binocular image in your Motic Microscope, it could be due to several factors. First, check if the magnification or field of view of the left and right eyepieces differ, and if so, match them. Ensure that the interpupillary distance is correctly adjusted. Also, verify that the eyepiece diopter is properly adjusted.
Ensures correct voltage supply for the microscope's operation and safety.
Instructions for using coarse/fine focus knobs, torque adjustment, and focus lock.
Procedure to adjust the stage's upper limit to prevent objective damage.
Guide to adjusting diopters for individual eyesight compensation.
How to adjust the aperture diaphragm for resolution, contrast, and depth of focus.
Steps for setting the polarizer and analyzer orientation for polarized light.
Procedure for focusing and centering the Bertrand lens for conoscopic observation.
Details on compensators, including 1/4-plate, 1λ-plate, and Quartz Wedge.
Detailed steps for safely replacing the halogen lamp bulb.
General| Brand | Motic |
|---|---|
| Model | BA310 Pol |
| Category | Microscope |
| Language | English |
To Next Page
