Motorola HD-DTA100u - User Manual

H D - D TA10 0 u
Quick Start Guide
Cable In
To TV
CH 3/4
Switch
HDMI
Power
The HD-DTA100u
will not turn on
• MakesurethePOWERLEDonthefrontoftheHD‑DTA100u
islitgreen.
• IftheHD‑DTA100uisconnectedtoaswitchedoutlet,make
suretheswitchisturnedon.Itisrecommendedtousean
unswitchedoutlet,ifpossible.
• UnplugtheHD‑DTA100ufromtheACoutlet,andthenplugit
backin.
• MakesuretheremotecontrolisinDTAmode,andturnthe
HD‑DTA100uonbypressingtheDTAbutton.
The remote
control does not
work
• MakesuretheremotecontrolisinDTAmode.
• Makesuretherearenoobstructionsbetweentheremote
controlandtheHD‑DTA100u.Aimtheremotecontroldirectly
attheHD‑DTA100ufrontpanel,nottheTVorVCR.
• TheanglebetweentheremotecontrolandtheHD‑DTA100u
maybetoolarge.StandinfrontoftheHD‑DTA100uandnot
toofartoeitherside.
• Pressandreleaseoperationbuttonsoneatatime,rmlyand
deliberately.
• Checkthebatteriesintheremotecontrol.Installnew
batteriesifneeded.
There is no video
on the TV screen
• MakesuretheTVisonandsettotheappropriateinput
sourcefortheHD‑DTA100u.
• MakesuretheHD‑DTA100uisonandtunedtoanauthorized
cablechannel.
• MakesurethecablesbetweentheHD‑DTA100uandtheTV
arermlyconnected.
• Makesurethecoaxialcablefeedisrmlyconnectedtothe
HD‑DTA100uandthewalljack.
There is no audio
when viewing
cable channels
• PressMUTEontheremotecontroltorestoresound.
No closed
captions display
• MakesureclosedcaptionsareenabledontheTV.(Note:
Closedcaptioningmaynotbeavailableforthecurrent
program.)
Troubleshooting
Checkherebeforecallingyourserviceprovider.

Summary

Troubleshooting HD-DTA100 u Issues

HD-DTA100 u Not Turning On

Check POWER LED, outlet status, and power cycle the device.

Remote Control Not Working

Verify DTA mode, clear obstructions, correct angle, press buttons firmly, and check batteries.

No Video on TV Screen

Confirm TV input, device tuning, and secure coaxial/HDMI connections.

No Audio on Cable Channels

Press MUTE on the remote to restore sound.

No Closed Captions Display

Ensure closed captions are enabled on the TV for the program.

Setting Up HD-DTA100 u and RF4 CE Remote

Connect Cable Service

Connect coaxial cable from wall outlet to the HD-DTA100u Cable In port.

Connect to TV

Use HDMI for HDTV or To TV connector for SDTV.

Power Connection

Plug the power cord into the HD-DTA100u and an unswitched electrical outlet.

TV Input Selection

Select correct HDMI input for HDTV or channel 3/4 for SDTV.

Install Remote Batteries

Insert batteries into the HD-DTA100u remote control.

Program RF4 CE Remote

Pair remote by pressing SETUP, then MENU, following on-screen prompts.

Motorola HD-DTA100u Specifications

General

Brand	Motorola
Model	HD-DTA100u
Category	Receiver
Language	English