Why does Motorola Barcode Reader emit one high beep when idle?
If your Motorola Barcode Reader emits one high beep when not in use, it's normal if the scanner is in RS-232 mode, a character was received, and the Beep on option is enabled.
What does it mean when Motorola Barcode Reader emits low/high beeps during programming?
If your Motorola Barcode Reader emits low/high beeps during programming, it means there was an input error or the Cancel barcode was scanned. Scan the correct numeric barcodes within range for the parameter programmed.
What does it mean when Motorola Barcode Reader emits low/high/low beeps?
If your Motorola Barcode Reader emits low/high/low beeps, it indicates that you are clearing the Code 39 buffer. This is normal when scanning the Code 39 Buffering Clear Buffer bar code or upon attempt to transmit an empty Code 39 buffer.
Why does Motorola Barcode Reader beep multiple times on power-up?
If your Motorola Barcode Reader emits the short low/short medium/short high beep sequence (power-up beep sequence) more than once, it's because the USB bus may be cycling the scanner's power on and off repeatedly. This is normal during host reset.
Why does Motorola Barcode Reader emit high/high/high/low beeps when not in use?
If your Motorola Barcode Reader emits high/high/high/low beeps when not in use, it indicates an RS-232 receive error. This is normal during host reset. Otherwise, set the scanner's RS-232 parity to match the host setting.
Why does Motorola Barcode Reader emit 4 short high beeps during decode?
If your Motorola Barcode Reader emits 4 short high beeps during a decode attempt, it indicates that the scanner has not completed USB initialization. Wait several seconds and scan again.
What to do if Motorola Barcode Reader emits aiming pattern but doesn't decode?
If your Motorola Barcode Reader emits an aiming pattern but doesn't decode the barcode, consider the following: * The scanner might not be programmed for the correct barcode type. Program the scanner to read that type of barcode. * The barcode symbol might be unreadable. Scan test symbols of the same barcode type to determine if the barcode is defaced. * The symbol may not be completely inside the aiming pattern. Move the symbol completely within the aiming pattern.
Why does Motorola Barcode Reader display scanned data incorrectly?
If your host displays scanned data incorrectly from your Motorola Barcode Reader, it could be due to the following reasons: * The scanner is not programmed to work with the host. Scan the appropriate host type programming bar code. * For RS-232, the scanner's communication parameters might not match the host's settings. Set the scanner's communication parameters to match the host's settings. * The editing options might be incorrect. Program the proper editing options (e.g., UPC-E to UPC-A Conversion).
How to fix Motorola Symbol DS6708 aiming pattern not appearing?
If the aiming pattern doesn't appear when you press the trigger on your Motorola Barcode Reader, consider these potential causes: * There may be no power to the scanner. If your configuration requires a power supply, reconnect it. * An incorrect host interface cable might be in use. Connect the correct cable. * Interface/power cables may be loose. Re-connect them. * The scanner could be disabled. Consult with the technical person in charge of scanning. * If using RS-232 Nixdorf B mode, CTS may not be asserted. Assert the CTS line. * The aiming pattern may be disabled. Enable the aiming pattern.
Why Motorola Symbol DS6708 emits low/high beeps during programming?
The Motorola Barcode Reader emits low/high beeps during programming due to an input error or because the Cancel bar code was scanned. To resolve this, scan the correct numeric bar codes within the valid range for the parameter you are programming.
General| Scanner Type | Handheld |
|---|---|
| Scan Pattern | Omni-directional |
| Scan Rate | 100 scans per second |
| Connectivity Technology | Wired |
| Interface | USB, RS-232 |
| Supported Barcodes | UPC, EAN, Code 39, Code 128, PDF417, Data Matrix |
| Operating Temperature | 32°F to 122°F |
| Storage Temperature | -40°F to 158°F |
| Drop Specification | 6 ft. drop to concrete |
| Light Source | Laser |
| Scanning Speed | 100 scans per second |
| Resolution | 0.1 mm |
| Humidity | 5% to 95% (non-condensing) |
To Next Page