EasyManua.ls Logo

motortronics MVC Plus - Page 41

Default Icon
79 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
- 37 -
5.1.11 设置页面 11 通讯设置(Page 11 Communications Configuration)
设置页面
密码等级
说明
出厂设置
范围
详细介绍
Page11
Communication
s
通讯
Lever 3
Password Protection
3 级密码保护
Set Front Baud Rate
设定 RS232 通讯波特率
9.6KB/sec
9.6KB/秒
2.4,4.8,9.6,19.2,38.4KB/sec
SP11.1
Set Modus Baud Rate
设定 Modus 通讯波特率
9.6KB/sec
9.6KB/秒
2.4,4.8,9.6,19.2,38.4KB/sec
SP11.2
Modus Address Number
Modus 地址
247
1-247
SP11.3
Set Access Code
设定接入代码
1
1-999
SP11.4
Set Link Baud Rate
设定 RS422 通讯波特率
38.4KB/sec
38.4KB/秒
2.4,4.8,9.6,19.2,38.4KB/sec
SP11.5
Remote Start/Stop
远程起动/停车
Disabled
无效
Enabled or Disabled
有效或无效
SP11.6
5.1.12 设置页面 12 系统设置(Page12 System Setpoint)
设置页面
密码等级
说明
出厂设置
范围
详细介绍
Page12
System Setpoints
系统设置
Lever 3
Password Protection
3 级密码保护
Default Display Screen
默认显示屏幕
SP12.1
Metering Data Page#
测量页面
1
Enter Metering Page(1-4)
测量页面(1-4)
Metering Data Screen#
测量页面屏幕
1
Enter Metering Screen测量页面屏幕
Page1(1-10) 页面 1(1-10)
Page2(1-11) 页面 2(1-11)
Page3(1-29) 页面 3(1-29)
Page4(1-16) 页面 4(1-6)
Alarms
报警
SP12.2
RTD Failure Alarm
RTD 故障报警
Disabled
无效
Enabled 或 Disabled
有效或无效
Thermal Register Alarm
热寄存器报警
90%
Off, 40-95%
无效,40-95%
Thermal Alarm Delay
热寄存器报警延时
10sec
10 秒
1-20sec
1-20 秒
Thermal Register SetupInfo
热寄存器设置
SP12.3
Cold Stall Time
冷态堵转时间
O/L Class
过载等级
O/L Class (5-30) or 4-40sec
5-30 级过载等级或 4-40 秒
Hot Stall Time
热态堵转时间
O/L Class
1
/
2
过载等级
1
/
2
O/L Class, 4-40sec
过载等级的一半,4-40 秒
Stopped Cool Down Time
停机冷却时间
30 Min
30 分钟
10-300 Min
10-300 分钟
Running Cool Down Time
运行冷却时间
15 Min
15 分钟
10-300 Min
10-300 分钟
Relay Measured Cool Rates
使用 RTD 测量冷却时间
Disabled
无效
Enabled or Disabled
有效或无效
Thermal Register Minimum
热寄存器最小值
15%
10-50%
Motor Design Ambient Temp
电动机设计环境温度
40℃
10-90℃
Motor Design Run Temp
电动机设计运行温度
80% Max
80%
50-100% of Motor Stator Max Temp
50-100%的电动机定子最高温度
Motor Stator Max Temp
电动机定子最大温度
INS CLS
绝缘等级
INS CLS, 10-240℃
绝缘等级,10-240℃
I/B Input to Thermal Register
电流不平衡输入热寄存器
Disabled
无效
Enabled or Disabled
有效或无效
Use Calculated K or Assign
使用自动或指定的系数 K
7
1-50,On
1-50 或自动
Press Enter to Clr Thermal Register
按 ENTER 键清除热寄存器
SP12.4