Need help?Do you have a question about the MSI X340 and is the answer not in the manual?
Move the 'Unlock' button as shown in the image to begin battery removal.
Release the 'Release' button and slide the battery pack base to remove it.
Insert and push the dummy card, then remove it after it pops up.
Remove the 10 screws (M2*2.5mm) securing the lower case.
Release the two middle keyboard hooks before removal.
Insert a tool under the keyboard to aid in its removal.
Release the side hooks and lift the keyboard from the top.
Use a plate to slide and remove the double-sided adhesive pad.
Carefully remove the keyboard from its housing.
Push the keyboard cable connector's sides and disconnect the cable.
Remove the 6 screws (M2*3.5mm) securing the upper case.
Begin removing the upper case from the right side, lifting and pushing.
Remove the left side of the upper case by lifting and pushing.
Detach the upper case from the lower case, minding the touchpad cable.
Release the connector and remove the touchpad cable.
Remove the 2 screws (M2*3.5mm) securing the HDD module.
Remove the HDD Module by following the indicated direction.
Remove the 3 screws (M3*3.5mm) stabilizing the HDD bracket.
Remove the HDD bracket components.
Remove the 2 screws (M2*3.5mm) securing the WLAN module.
Remove the WLAN board as depicted in the image.
Disconnect and remove the wireless card antennas.
Remove the single screw (M2*3.5mm) from the WLAN module.
Remove the WLAN module following the indicated direction.
Disconnect and remove the LVDS cable.
Disconnect and remove the LINK cable.
Remove the speaker and microphone cables.
Remove the 3 screws (M2*3.5mm) securing components.
Remove the right side I/O board.
Remove LINK cable, Audio cover, and DCIN cover from the I/O board.
Remove the 4 screws (M2*3.5mm) from the right hinge.
Remove the 3 screws (M2*3.5mm) from the left hinge.
Push the side shielding of the RAM module to release it.
Remove the RAM module following the indicated direction.
Remove the 3 screws (M2*3.5mm).
Remove the left side I/O port assembly.
Remove DSUB and MODE covers from the left I/O board.
Disconnect and remove the Bluetooth cable.
Remove the single screw (M2*3.5mm).
Remove the Bluetooth module.
Remove Mylar, 3 screws, and then the heatsink.
Remove 2 screws (M2*3.5mm).
Remove 2 screws (M2*3.5mm).
Remove the main board and pull out the fan cable.
Remove the fan from the main board.
Remove the left HDMI cover from the lower case.
Remove the SD card cover from the lower case.
Remove the right USB cover from the lower case.
Remove 3 screws and the speaker module from the lower case.
Release connector and remove the T/P module.
Remove 2 screws and the touchpad board from the upper case.
Remove Mylar from T/P module, then remove the T/P module.
Remove 4 cover rubbers and 1 bezel rubber.
Insert stick into hinge cap to remove it.
Start LCD bezel removal from the top side.
Push the bezel at the 5 bottom hooks to separate it from the panel.
Lift bezel bottom, press Mylar with stick to remove adhesive.
Remove the LCD bezel from the sides.
Remove the 3 magnets from the LCD bezel.
Remove 8 screws (M2*3mm) securing the LCD hinges.
Remove the left and right LCD hinges.
Remove hook sponges and hooks from the panel sides.
Carefully raise and remove the display module, minding the LCD cable.
Remove tape stabilizing LVDS cable, then remove the LVDC cable.
Remove the display module from the LCD cover.
Remove the coaxial camera cable following the sequence.
Remove CMOS camera module carefully to avoid damage.
Remove the MIC sponge covering the MIC module.
Remove MIC module, aligning it with the LCD cover dent.
Remove the antenna board from the LCD cover.
To Next Page
General
