mspa U-AU061 User Manual (English)

Questions and Answers:

R
Rachel HillAug 13, 2025
Why is my mspa U-AU061 not heating properly?
- M
  Matthew GarzaAug 14, 2025
  Your MSpa Hot Tub might not be heating properly due to several reasons. Check if the temperature is set too low and increase it. A dirty filter cartridge can also cause this, so clean or replace it. Ensure the water level is at least at the minimum line. If these steps don't resolve the issue, there may be a heater failure, or the filter pump may not be working; in the latter case, refer to the section on 'FILTER PUMP DOES NOT WORK'.
J
John AndersonAug 18, 2025
How to clean the water in my mspa U-AU061 Hot Tub?
- D
  dmurilloAug 18, 2025
  To clean the water in your MSpa Hot Tub, start by changing the water if it has been used for a long time. Ensure you extend the filtration time. Regularly clean or replace the filter cartridge. Also, maintain proper water balance by referring to the chemical manufacturer’s instructions.
D
Douglas RyanAug 21, 2025
What to do if my MSpa Hot Tub is leaking?
- P
  Pam KimAug 21, 2025
  If your MSpa Hot Tub is leaking, first check whether the spa in&outlet connection is securely tight and tighten it if necessary. Ensure the drainage valve is completely closed. If the spa pool body is leaking, repair the hole or split using the repair kit material.
C
Cheryl RivasAug 25, 2025
Why is my MSpa Hot Tub losing air?
- L
  Lisa SanfordAug 26, 2025
  Your MSpa Hot Tub might be losing air because the air valve is loose. Inflate the spa until the yellow section of the manometer is pushed out and ensure the valve is screwed tightly; replace the valve if needed. Another reason could be a hole or split on the spa tub. To locate it, fill a squirt bottle with soapy water and spray on the seams; small bubbles will appear where there is a leak. Clean and dry the leaking area, then use the repair patch supplied with your spa.
A
Ashley DayAug 28, 2025
What to do if there is no display on the control panel of my mspa U-AU061 Hot Tub?
- F
  Frank BakerAug 28, 2025
  If there is no display on the control panel of your MSpa Hot Tub, first check the power socket and change or repair it if it's faulty. If the socket is fine, reset the PRCD by following the PRCD Testing section. If the controller is still not displayed after pressing the reset button, it might indicate a broken PRCD.
J
Jessica TaylorSep 1, 2025
How to fix a MSpa Hot Tub that loses air?
- E
  ellisjeffreySep 1, 2025
  If your MSpa Hot Tub is losing air, ensure the air valve is tightly screwed in and inflate the spa until the yellow section of the manometer is pushed out. If necessary, replace the valve. Also, inspect the spa tub for holes or splits by applying soapy water to the seams; repair any leaks with the provided patch.
M
Michael KeithSep 5, 2025
How to fix no display on the mspa U-AU061 control panel?
- C
  charles58Sep 5, 2025
  If there is no display on the control panel of your MSpa Hot Tub, first check the power socket. Change the socket or repair the socket before use if it has failed. Also, check if the PRCD is off and reset it by following the PRCD Testing section. If, after pressing the Reset button, the controller is still not displayed, it may be broken.
D
Diane MaySep 9, 2025
Why is my MSpa Hot Tub in an abnormal shape?
- M
  Mr. Jon GonzalezSep 9, 2025
  If your MSpa Hot Tub is in an abnormal shape, it could be due to extra air pressure from strong sunlight. Check the air pressure and release air if necessary. During hot weather, it is advisable to check whether some air should be released to avoid any possible damage to the spa pool.

mspa U-AU061 Specifications

General

Model	U-AU061
Category	Hot Tub
Type	Inflatable
Heater	1500W
Temperature Range	20-40°C
Capacity	6 people
Water Capacity	930 Liters
Dimensions	204 x 70 cm
Net Weight	Approx. 84 lbs (38 kg)
Filter Pump	1325L/hr
Material	6-layer reinforced PVC
Heating System	PTC
Jet System	Air Jet