Why is my MSpa Hot Tub not heating properly?
If your MSpa Hot Tub is not heating properly, first ensure that the temperature is set high enough. If the temperature is already set high, check that the water level is at least at the minimum water line. If neither of these solutions work, the heating element may have failed, in which case you should contact the MSpa Service Center.
How to clean the water in my mspa Lite LR06-GR?
If the water in your MSpa Hot Tub is not clean, you can extend the filtration time. Also, you should clean or replace the filter cartridge in time. If the problem persists, refer to the chemical manufacturer’s instruction for proper water maintenance.
How to stop my mspa Lite LR06-GR Hot Tub from losing air?
If your MSpa Hot Tub is losing air, first check if the air valve is loose. Inflate the spa until the yellow section of the manometer is pushed out and ensure the valve is screwed tightly, replace it if necessary. Also, inspect the spa tub for holes or splits. Fill a squirt bottle with soapy water and spray on the seams. If there is a leak, small bubbles will come out. Clean and dry the leaking area, then use the repair patch supplied with your spa.
What to do if the filter pump does not work on my MSpa Hot Tub?
If your MSpa Hot Tub's filter pump isn't working, first check the power supply. If the power is fine, the filter cartridge may be clogged with dirt or other objects; try cleaning or replacing it. Also, ensure the water level is sufficient, adding more water until it reaches the minimum water line.
How to fix a MSpa Hot Tub that loses air?
If you find your MSpa Hot Tub is losing air, start by checking the air valve to ensure it's tightened. Inflate the spa until the yellow section of the manometer is pushed out and make sure the valve is screwed tightly. If necessary, replace the valve. If the valve is not the problem, check for holes or splits on the spa tub by applying soapy water to the seams. If you see bubbles, clean and dry the area, then use the provided repair patch to fix the leak.
What to do if there is no display on the control panel of my mspa Lite LR06-GR?
If there is no display on the control panel of your MSpa Hot Tub, start by checking the power supply to ensure it is working. If the power supply is fine, check if the PRCD is off and reset it by following the PRCD Testing section. If the PRCD continues to fail, it may be broken, and you should contact the MSpa Service Center.
Why doesn't the bubble air blower work on my mspa Lite LR06-GR Hot Tub?
If the bubble air blower on your MSpa Hot Tub is not working, and it is not a bubble motor failure (in this case you should contact the MSpa Service Center), it may have automatically turned off after 10 minutes. Wait for 10 minutes before turning the bubble button on again.
Why is my MSpa Hot Tub in an abnormal shape?
If your MSpa Hot Tub is in an abnormal shape, it may be due to extra air pressure caused by strong sunshine. Check the air pressure and release air if necessary. During hot weather, it is recommended to check if it is necessary to release some air to avoid any possible damage to the spa pool.
What to do if my mspa Lite LR06-GR is leaking?
If your MSpa Hot Tub is leaking, first tighten the in&outlet connection. If the spa is still leaking, ensure the drainage valve is completely closed. If the problem persists, repair any holes or splits in the spa pool body using the repair kit material.
How to fix no display on the control panel of mspa Lite LR06-GR Hot Tub?
If there is no display on the control panel of your MSpa Hot Tub, check the power socket. Change to a working socket or repair the existing one if it's faulty. Also, check if the PRCD is off and reset it by following the PRCD Testing section.
Details critical risks like drowning and electric shock requiring extreme caution.
Outlines essential electrical safety measures, grounding, and appliance connection requirements.
Details site selection, surface requirements, drainage, and clearance necessary for spa installation.
Explains the mandatory testing procedure for the PRCD to ensure electrical safety before use.
Guides on inflating the spa using the inflation hose and manometer, including pressure indicators.
Details how to deflate the spa and fill it with water, including warnings about water levels.
Describes how to operate the Heater and Filter buttons, including status indicators.
Emphasizes cleaning, sanitizing, and maintaining water parameters like pH and chlorine levels.
Details practical steps for maintaining spa water and cleaning the filter cartridge.
Step-by-step guide for draining water from the spa and its piping system.
Explains error codes, their causes, and corresponding solutions for system issues.
General| Type | Portable Hot Tub |
|---|---|
| Capacity | 4-6 people |
| Heating System | Electric |
| Heater | 1500W |
| Massage Air Blower | Yes |
| Filter Pump | Yes |
| Material | PVC |
| Temperature Range | 20°C - 42°C (68°F - 104°F) |
| Jet System | Air Jets |
| Control System | Digital Control Panel |
To Next Page
