mspa OSLO User Manual (English)

Questions and Answers:

M
Michelle HernandezAug 20, 2025
Why is my mspa OSLO Hot Tub not heating properly?
- T
  Terrance BarnesAug 20, 2025
  If your MSpa Hot Tub isn't heating properly, here are a few things to check: 1. Temperature Setting: Ensure the temperature is set high enough. 2. Filter Cartridge: A dirty filter cartridge can hinder heating. Clean or replace it. 3. Water Level: Make sure the water level reaches at least the minimum line; add water if needed. 4. Heater Failure: Contact your local MSpa Service Center. 5. Filter Pump: Refer to the "FILTER PUMP DOES NOT WORK" section.
B
Bradley NelsonAug 22, 2025
How to clean the water in my MSpa Hot Tub?
- D
  Darrell GreenAug 22, 2025
  If the water in your MSpa Hot Tub isn't clean, consider these points: * Old Water: If the water has been in use for a long time, it's time for a change. * Insufficient Filtration: Increase the duration of filtration. * Dirty Filter Cartridge: Regularly clean or replace the filter cartridge. * Improper Water Maintenance: Follow the chemical manufacturer’s instructions for water maintenance.
R
Rebekah HernandezAug 25, 2025
What to do if the water in my MSpa Hot Tub is not clean?
- B
  Becky SanchezAug 25, 2025
  If the water in your MSpa Hot Tub is not clean, it might be because the water has been used for a long time, so you should change it. Also, try extending the filtration time or cleaning/replacing the filter cartridge. For proper water maintenance, refer to the chemical manufacturer’s instructions.
L
Lori RamirezAug 26, 2025
Why is there no display on my mspa OSLO Hot Tub control panel?
- M
  Michelle HatfieldAug 26, 2025
  If the control panel on your MSpa Hot Tub isn't displaying anything, the issue might stem from a few causes: * A faulty power socket: Try using a different socket, or have the current one repaired. * The GFCI being off: Reset it by following the instructions in the GFCI Testing section. * The controller not working: Contact your local MSpa Service Center. * A broken GFCI: Contact your local MSpa Service Center.
S
stephanie70Aug 27, 2025
What to do if my MSpa Hot Tub is leaking?
- F
  folsonAug 28, 2025
  If your MSpa Hot Tub is leaking, check the following: * In&outlet Connection: Make sure the spa's in&outlet connections are securely tightened. * Drainage Valve: Ensure the drainage valve is completely closed. If leaking persists, contact the MSpa Service Center.
M
Mrs. Alicia LyonsAug 29, 2025
Why doesn't the filter pump work on my mspa OSLO Hot Tub?
- E
  etuckerAug 30, 2025
  If the filter pump on your MSpa Hot Tub isn't working, it could be due to: * Clogged Filter Cartridge: Clean or replace the filter cartridge if it's blocked by dirt or other objects. * Filter System Failure: Contact your local MSpa Service Center.
T
Tina CollinsSep 1, 2025
Why is the jet function failing on my mspa OSLO Hot Tub (without icon)?
- N
  Noah CaldwellSep 1, 2025
  If the jet function on your MSpa Hot Tub is not working (without icon), consider the following: * Water Level: Ensure the water level is above the minimum line by adding more water. * Water Inlet Blockage: Clean the filter pump and jet pump inlets. * Filter Pump Issue: Refer to the "FILTER PUMP DOES NOT WORK“ section.
K
Kristina HolmesSep 3, 2025
Why is there no bubble in my mspa OSLO Hot Tub?
- A
  Arthur BrownSep 3, 2025
  If you're not getting any bubbles from your MSpa Hot Tub, it might be because: * Auto-off: The bubble function automatically turns off after 10 minutes. Wait 10 minutes before turning it back on. * Damaged Internal Parts: Contact your local MSpa Service Center. * Broken One-way Valve: Contact your local MSpa Service Center.
R
Richard EstradaSep 4, 2025
Why is the jet function failing on my mspa OSLO Hot Tub (with icon)?
- K
  Kimberly DavidsonSep 4, 2025
  If the jet function on your MSpa Hot Tub is failing (with icon), it could be due to: * Low Water or Ambient Temperature: Heat the water up to 68 °F (20 °C). * Sensitive Protection System: Ensure the water temperature is above 68 °F (20 °C). Long press the JET button for 3 seconds to unlock the JET function. If this doesn’t work, continue heating the water and try again later.
A
amanda59Sep 7, 2025
What causes ozonator failure in mspa OSLO Hot Tub?
- G
  Gerald VazquezSep 7, 2025
  If the ozonator on your MSpa Hot Tub is failing, check these: * Water Level: Ensure the water level is above the minimum line by adding more water. * Damaged Internal Parts: Contact your local MSpa Service Center. * Filter Pump: Refer to the "FILTER PUMP DOES NOT WORK" section.