Why is my mspa Lite LS06-GR Hot Tub not heating properly?
If your MSpa Hot Tub is not heating properly, first ensure that the temperature is set high enough. If the temperature is already set high, check that the water level is at least at the minimum water line. If neither of these solutions work, the heating element may have failed, in which case you should contact the MSpa Service Center.
How to clean the water in my mspa Lite LS06-GR Hot Tub?
If the water in your MSpa Hot Tub is not clean, you can extend the filtration time. Also, you should clean or replace the filter cartridge in time. If the problem persists, refer to the chemical manufacturer’s instruction for proper water maintenance.
How to stop my mspa Hot Tub from losing air?
If your MSpa Hot Tub is losing air, first check if the air valve is loose. Inflate the spa until the yellow section of the manometer is pushed out and ensure the valve is screwed tightly, replace it if necessary. Also, inspect the spa tub for holes or splits. Fill a squirt bottle with soapy water and spray on the seams. If there is a leak, small bubbles will come out. Clean and dry the leaking area, then use the repair patch supplied with your spa.
What to do if the filter pump does not work on my MSpa Hot Tub?
If your MSpa Hot Tub's filter pump isn't working, first check the power supply. If the power is fine, the filter cartridge may be clogged with dirt or other objects; try cleaning or replacing it. Also, ensure the water level is sufficient, adding more water until it reaches the minimum water line.
How to fix a mspa Lite LS06-GR that loses air?
If you find your MSpa Hot Tub is losing air, start by checking the air valve to ensure it's tightened. Inflate the spa until the yellow section of the manometer is pushed out and make sure the valve is screwed tightly. If necessary, replace the valve. If the valve is not the problem, check for holes or splits on the spa tub by applying soapy water to the seams. If you see bubbles, clean and dry the area, then use the provided repair patch to fix the leak.
What to do if there is no display on the control panel of my mspa Lite LS06-GR?
If there is no display on the control panel of your MSpa Hot Tub, start by checking the power supply to ensure it is working. If the power supply is fine, check if the PRCD is off and reset it by following the PRCD Testing section. If the PRCD continues to fail, it may be broken, and you should contact the MSpa Service Center.
Why doesn't the bubble air blower work on my mspa Lite LS06-GR Hot Tub?
If the bubble air blower on your MSpa Hot Tub is not working, and it is not a bubble motor failure (in this case you should contact the MSpa Service Center), it may have automatically turned off after 10 minutes. Wait for 10 minutes before turning the bubble button on again.
Why is my mspa Lite LS06-GR Hot Tub in an abnormal shape?
If your MSpa Hot Tub is in an abnormal shape, it may be due to extra air pressure caused by strong sunshine. Check the air pressure and release air if necessary. During hot weather, it is recommended to check if it is necessary to release some air to avoid any possible damage to the spa pool.
What to do if my mspa Lite LS06-GR is leaking?
If your MSpa Hot Tub is leaking, first tighten the in&outlet connection. If the spa is still leaking, ensure the drainage valve is completely closed. If the problem persists, repair any holes or splits in the spa pool body using the repair kit material.
How to fix no display on the control panel of mspa Lite LS06-GR?
If there is no display on the control panel of your MSpa Hot Tub, check the power socket. Change to a working socket or repair the existing one if it's faulty. Also, check if the PRCD is off and reset it by following the PRCD Testing section.
The spa can be installed indoor and outdoor around 10 minutes by at least one person. For household use only.
Open the air blower inflation outlet and connect with the inflation hose as Figure 3.1.
Check the spa liner is at the selected area and point the drain valve toward a suitable draining area before filling water.
Heater, Filter, and Bubble buttons for core spa operations.
Adjustment Buttons, Controller Locking, and Timer Button for enhanced control.
The spa owner must regularly check and keep the spa water sanitized with scheduled maintenance.
Follow below instructions to maintain the spa water.
LED READING E0: Water temperature is lower than zero degree or exceed 55°C.
Addresses issues with the bubble blower and filter pump operation.
General| Model | Lite LS06-GR |
|---|---|
| Category | Hot Tub |
| Air Jets | Yes |
| Number of Jets | 120 |
| Power | 1500 W |
| Control System | Digital control panel |
| Massage Air Blower | Yes |
| Filter Pump | Yes |
| Voltage | 220-240 V |
| Color | Gray |
| Material | PVC |
| Water Capacity | 800 L |
| Temperature Range | 20 - 42 °C |
| Frequency | 50 Hz |
| Control Panel | Digital |
| Type | Inflatable Spa |
| Heat Increasing Rate | 1.5 - 2 °C/h |
To Next Page
