To Next PageTo Next PageWhat to do if there is no display on the mspa TUSCANY Hot Tub control panel?
If the control panel on your MSpa Hot Tub has no display, begin by checking the power socket; it may have failed and needs repair or replacement. If the socket is functional, reset the PRCD following the PRCD Testing section.
How to clean mspa TUSCANY water?
If your MSpa Hot Tub water is not clean, try these steps: change the water if it has been used for a long time. Increase the filtration time. Clean or replace the filter cartridge promptly. For proper water maintenance, refer to the chemical manufacturer’s instructions.
What to do if filter pump does not work on MSpa Hot Tub?
If the filter pump on your MSpa Hot Tub isn't working, first, check the filter cartridge for clogs caused by dirt or other objects, and clean or replace it. If the filter system has failed, contact the MSpa Service Center.
Why bubble air blower does not work on mspa TUSCANY?
If the bubble air blower on your MSpa Hot Tub isn't working, wait for 10 minutes and try turning the Bubble button on again, as it may have auto-off after 10 minutes. If it still doesn't work, the internal parts might be damaged, and you should contact the MSpa Service Center.
What to do if my mspa TUSCANY is leaking?
If your MSpa Hot Tub is leaking, start by checking the in&outlet connections to ensure they are securely tightened. Also, verify that the drainage valve is completely closed. If water is leaking from the spa pool body itself, use the repair kit material to patch any holes or splits.
What causes ozonator failure in my mspa TUSCANY Hot Tub?
If the ozonator fails in your MSpa Hot Tub, ensure the water level is at least at the minimum line by adding more water. If the issue continues, the one-way valve may be blocked, or the filter pump may not be working, requiring you to contact the MSpa Service Center or refer to the "FILTER PUMP DOES NOT WORK" section.
What to do if there is no display on my mspa TUSCANY wired controller?
If your MSpa Hot Tub's wired controller has no display, first check the power supply. If that's fine, reset the PRCD following the PRCD Testing section. If the PRCD is broken or the control panel doesn't display after pressing the reset button, contact the MSpa Service Center.
How to fix a leaking mspa TUSCANY?
If the MSpa Hot Tub is leaking, ensure the spa inlet/outlet connections are securely tightened. If water leaks from the spa liner, repair the hole with the repair kit material. If the drainage valve is not closed completely, contact the MSpa Service Center.
How to fix no display on mspa TUSCANY Hot Tub control panel?
If there's no display on your MSpa Hot Tub's control panel, first, try using a different power socket or have the current one repaired. If that doesn't work, reset the PRCD following the PRCD Testing section. If the controller still doesn't display after pressing the Reset button, or if the PRCD is broken, contact the MSpa Service Center.
What does error E1 mean on my mspa TUSCANY Hot Tub?
If your MSpa Hot Tub displays an E1 error, it could be due to a water flow switch failure, in which case you should contact the MSpa Service Center. Alternatively, the water level might be below the minimum line, so add water above the minimum line. Filter failure can also cause this error.
Steps for preparing the installation site, including surface and clearance for the spa.
Specifics for indoor installations, focusing on floor support and moisture resistance.
Specifics for outdoor installations, focusing on surface, sun exposure, and temperature.
Procedure for testing the PRCD (Residual Current Protection Device) before each use.
Instructions for assembling the spa wall structure using panels and corner beams.
Steps for installing the spa liner into the wall frame and securing it properly.
Guidance on connecting the control box to the spa pool with sealing rings.
Instructions for inflating the spa's air bladder using the provided foot pump.
Details on how to fill the spa with water to the correct minimum and maximum levels.
Instructions for operating the spa cover buckles, including locking and unlocking.
How to start, stop, and understand the status of the heating function.
Instructions for turning the filtration function on/off and its auto-filtration.
How to adjust bubble massage levels and understanding its operation limitations.
How to adjust the water temperature using the UP/DOWN buttons.
Procedure for locking and unlocking the control panel to prevent accidental changes.
How to set a pre-set heating timer for automatic operation up to 99 hours.
How to switch between Celsius and Fahrenheit temperature displays.
How to activate the Ozonator and its operational limits and safety concerns.
How to clear the filter cleaning reminder when the FILTER icon flashes.
Importance of sanitizing and maintaining water balance for hygiene and spa lifespan.
Guidelines for maintaining proper water balance parameters like pH and chlorine levels.
Precautions and procedures for adding spa water chemicals safely and correctly.
Steps for installing, cleaning, and replacing the spa filter cartridge.
Procedures for changing spa water, chemical use, hygiene, and cleaning components.
Step-by-step instructions for draining the spa water using the drain valve.
How to clean the spa tub interior after draining, avoiding abrasive cleaners.
Instructions for repairing punctures in the spa tub or air bladder using the repair patch.
Procedures for draining, cleaning, and storing the spa for off-season or long periods.
Chart listing LED error codes, their causes, and corresponding solutions.
Troubleshooting for issues like no display, heating, or bubble blower not working.
Troubleshooting steps for ozonator failure and filter pump malfunction.
Solutions for spa leaks and common issues with water clarity and cleanliness.
Details on shipping, warranty terms, limitations, and registration procedures.
Steps for preparing the installation site, including surface and clearance for the spa.
Specifics for indoor installations, focusing on floor support and moisture resistance.
Specifics for outdoor installations, focusing on surface, sun exposure, and temperature.
Procedure for testing the PRCD (Residual Current Protection Device) before each use.
Instructions for assembling the spa wall structure using panels and corner beams.
Steps for installing the spa liner into the wall frame and securing it properly.
Guidance on connecting the control box to the spa pool with sealing rings.
Instructions for inflating the spa's air bladder using the provided foot pump.
Details on how to fill the spa with water to the correct minimum and maximum levels.
Instructions for operating the spa cover buckles, including locking and unlocking.
How to start, stop, and understand the status of the heating function.
Instructions for turning the filtration function on/off and its auto-filtration.
How to adjust bubble massage levels and understanding its operation limitations.
How to adjust the water temperature using the UP/DOWN buttons.
Procedure for locking and unlocking the control panel to prevent accidental changes.
How to set a pre-set heating timer for automatic operation up to 99 hours.
How to switch between Celsius and Fahrenheit temperature displays.
How to activate the Ozonator and its operational limits and safety concerns.
How to clear the filter cleaning reminder when the FILTER icon flashes.
Importance of sanitizing and maintaining water balance for hygiene and spa lifespan.
Guidelines for maintaining proper water balance parameters like pH and chlorine levels.
Precautions and procedures for adding spa water chemicals safely and correctly.
Steps for installing, cleaning, and replacing the spa filter cartridge.
Procedures for changing spa water, chemical use, hygiene, and cleaning components.
Step-by-step instructions for draining the spa water using the drain valve.
How to clean the spa tub interior after draining, avoiding abrasive cleaners.
Instructions for repairing punctures in the spa tub or air bladder using the repair patch.
Procedures for draining, cleaning, and storing the spa for off-season or long periods.
Chart listing LED error codes, their causes, and corresponding solutions.
Troubleshooting for issues like no display, heating, or bubble blower not working.
Troubleshooting steps for ozonator failure and filter pump malfunction.
Solutions for spa leaks and common issues with water clarity and cleanliness.
Details on shipping, warranty terms, limitations, and registration procedures.
The MSpa Tuscany is a portable hot tub designed to provide a luxurious and relaxing spa experience. It is suitable for both indoor and outdoor use, offering flexibility in placement. The spa is designed for household use and emphasizes ease of setup and maintenance.
The MSpa Tuscany functions as a bubble spa, providing a soothing massage experience through its integrated air blower. The control system allows users to manage various functions, including heating, filtration, and bubbling. The heater maintains the water temperature up to 40°C (104°F), ensuring a warm and comfortable soak. The filtration system, with its replaceable cartridges, helps keep the water clean. An integrated ozone generator further enhances water sanitation by producing ozone, which helps in disinfection. The spa also features a timer function for pre-setting heating schedules, allowing users to have the spa ready at a desired time.
The Tuscany spa is designed for user-friendly operation. The wired control panel provides intuitive access to all functions. Users can easily adjust the water temperature, activate the bubble massage at different intensity levels (300W, 500W, 720W), and turn on the filtration system. The control panel also includes a Celsius/Fahrenheit toggle for temperature display preference. For safety, the bubbling massage function automatically shuts off after 20 minutes and cannot be reactivated for 10 minutes. The ozonator, which aids in water purification, operates independently for 2 hours before automatically turning off, and it cannot be used simultaneously with the bubbling function. A controller locking feature is available to prevent accidental changes to settings. The spa is equipped with a PRCD (Portable Residual Current Device) on the power cord, which must be tested before each use to ensure electrical safety. The spa cover, which includes an inflatable bladder for heat preservation, can be securely locked with buckles and a key, preventing unauthorized access and helping to maintain water temperature. The design allows for straightforward water filling and drainage, with a dedicated drain valve and adapter for connecting a garden hose.
Maintaining the MSpa Tuscany involves regular water care and cleaning. The filter cartridge is a key component for water quality and requires regular inspection and cleaning after each use. A cleaning reminder on the control panel flashes when the filter cartridge needs attention, prompting users to clean or replace it. The cartridge base is designed for easy installation and removal. For optimal performance and hygiene, the spa water should be changed every 3-5 days, depending on usage. Proper water chemistry is crucial, and users are advised to regularly check pH, free chlorine, bromine residual, total alkalinity, and total hardness levels, adjusting them with appropriate spa chemicals according to manufacturer instructions. It is important to add chemicals to water, not the other way around, to avoid strong reactions. The spa tub itself can be cleaned with a sponge and mild soap solution when empty, and it should be thoroughly rinsed. For minor punctures, a repair kit with patches is included. When storing the spa, it should be completely drained, cleaned, and dried, then deflated and disassembled. The original packaging is recommended for storage in a dry, temperature-controlled environment to protect the components. The manual also provides a troubleshooting guide with error codes and solutions for common issues, such as heating problems, filter pump malfunctions, and water quality concerns, directing users to contact MSpa service for more complex problems.
General| Air Jets | 138 |
|---|---|
| Number of Jets | 138 |
| Capacity | 6 persons |
| Water Capacity | 930 liters |
| Heat Increasing Rate | 1.2 - 1.8°C/hr |
| Seating Capacity | 6 persons |
| Voltage | 220-240V |
| Material | PVC |
| Filter | Filter Cartridge |
| Pump | 12V / 35W |
