To Next PageTo Next PageWhy does the bubble air blower on my mspa TUSCANY not work?
If the bubble air blower on your MSpa Hot Tub doesn't work, wait for 10 minutes in case it auto-off after 10 minutes. If the issue persists, the unidirectional threshold might not be open or there could be a control panel failure, requiring you to contact the MSpa Service Center.
What to do if the filter pump on my mspa TUSCANY doesn't work?
If the filter pump on your MSpa Hot Tub isn't working, start by cleaning or replacing the filter cartridge if it's clogged with dirt or other objects. If this doesn't solve the problem, there may be a filter system failure, requiring you to contact the MSpa service center.
Why is the water in my mspa TUSCANY Hot Tub not clean?
If the water in your MSpa Hot Tub is not clean, change the water if it has been used for too long. Also, increase filtration frequency if filtering is insufficient. If the filter cartridge is dirty, clean or replace it in time. For improper water maintenance, refer to the chemical manufacturer's instructions.
Why is my mspa TUSCANY losing air?
If your MSpa Hot Tub (Mono) is losing air, first check the air valve to ensure it's screwed tightly. If necessary, replace the valve and inflate the spa to 12 PSI. If the issue persists, there may be a hole or split in the spa tub. To locate it, apply soapy water to the seams; bubbles will appear where there's a leak. Clean and dry the area before applying the repair patch provided with your spa.
What to do if my mspa TUSCANY is leaking?
If your MSpa Hot Tub is leaking, start by checking the in&outlet connections to ensure they are securely tightened. Also, verify that the drainage valve is completely closed. If water is leaking from the spa pool body itself, use the repair kit material to patch any holes or splits.
Why bubble air blower does not work on mspa TUSCANY?
If the bubble air blower on your MSpa Hot Tub isn't working, wait for 10 minutes and try turning the Bubble button on again, as it may have auto-off after 10 minutes. If it still doesn't work, the internal parts might be damaged, and you should contact the MSpa Service Center.
What to do if filter pump does not work on MSpa Hot Tub?
If the filter pump on your MSpa Hot Tub isn't working, first, check the filter cartridge for clogs caused by dirt or other objects, and clean or replace it. If the filter system has failed, contact the MSpa Service Center.
How to clean mspa TUSCANY water?
If your MSpa Hot Tub water is not clean, try these steps: change the water if it has been used for a long time. Increase the filtration time. Clean or replace the filter cartridge promptly. For proper water maintenance, refer to the chemical manufacturer’s instructions.
General| Air Jets | 138 |
|---|---|
| Number of Jets | 138 |
| Capacity | 6 persons |
| Water Capacity | 930 liters |
| Heat Increasing Rate | 1.2 - 1.8°C/hr |
| Seating Capacity | 6 persons |
| Voltage | 220-240V |
| Material | PVC |
| Filter | Filter Cartridge |
| Pump | 12V / 35W |
Steps for preparing the installation site, including surface and clearance for the spa.
Specifics for indoor installations, focusing on floor support and moisture resistance.
Specifics for outdoor installations, focusing on surface, sun exposure, and temperature.
Procedure for testing the PRCD (Residual Current Protection Device) before each use.
Instructions for assembling the spa wall structure using panels and corner beams.
Steps for installing the spa liner into the wall frame and securing it properly.
Guidance on connecting the control box to the spa pool with sealing rings.
Instructions for inflating the spa's air bladder using the provided foot pump.
Details on how to fill the spa with water to the correct minimum and maximum levels.
Instructions for operating the spa cover buckles, including locking and unlocking.
How to start, stop, and understand the status of the heating function.
Instructions for turning the filtration function on/off and its auto-filtration.
How to adjust bubble massage levels and understanding its operation limitations.
How to adjust the water temperature using the UP/DOWN buttons.
Procedure for locking and unlocking the control panel to prevent accidental changes.
How to set a pre-set heating timer for automatic operation up to 99 hours.
How to switch between Celsius and Fahrenheit temperature displays.
How to activate the Ozonator and its operational limits and safety concerns.
How to clear the filter cleaning reminder when the FILTER icon flashes.
Importance of sanitizing and maintaining water balance for hygiene and spa lifespan.
Guidelines for maintaining proper water balance parameters like pH and chlorine levels.
Precautions and procedures for adding spa water chemicals safely and correctly.
Steps for installing, cleaning, and replacing the spa filter cartridge.
Procedures for changing spa water, chemical use, hygiene, and cleaning components.
Step-by-step instructions for draining the spa water using the drain valve.
How to clean the spa tub interior after draining, avoiding abrasive cleaners.
Instructions for repairing punctures in the spa tub or air bladder using the repair patch.
Procedures for draining, cleaning, and storing the spa for off-season or long periods.
Chart listing LED error codes, their causes, and corresponding solutions.
Troubleshooting for issues like no display, heating, or bubble blower not working.
Troubleshooting steps for ozonator failure and filter pump malfunction.
Solutions for spa leaks and common issues with water clarity and cleanliness.
Details on shipping, warranty terms, limitations, and registration procedures.
