Why MTD Snow Blower has excessive vibration?
Excessive vibration in your MTD Snow Blower may be due to loose parts or a damaged auger. Immediately stop the engine and disconnect the spark plug wire. Tighten all bolts and nuts. If the vibration continues, have the unit serviced by an authorized Service Center.
How to fix MTD Snow Blower engine that fails to start?
If your MTD Snow Blower engine won't start, several factors could be at play. First, ensure the choke is in the CHOKE position and the spark plug wire is securely connected. Next, check that the fuel tank isn't empty or filled with stale fuel; if so, replenish it with clean, fresh fuel. Make sure you've primed the engine as per the Engine Manual. Inspect the spark plug for faults, cleaning, adjusting the gap, or replacing it if necessary. Verify the safety key is fully inserted into the switch. Lastly, if your model has an electric start, confirm the extension cord is properly connected to both the snow blower and a grounded 120V AC outlet.
What to do if MTD 500 engine fails to start?
If your MTD Snow Blower engine won't start, here's what you can check: 1. Ensure the choke control is in the ON position. 2. Make sure the spark plug wire is securely connected. 3. Verify the fuel tank isn't empty and contains fresh gasoline. 4. Prime the engine as detailed in the Operation section of your manual. 5. Inspect the spark plug; clean, adjust the gap, or replace it if necessary. 6. Confirm the safety key is fully inserted into the switch.
Why MTD Lawn Mower engine fails to start?
The MTD Lawn Mower engine might fail to start due to several reasons. It could be that the blade control handle is disengaged (engage it), the spark plug wire is disconnected (connect it), the fuel tank is empty or contains stale fuel (fill it with clean, fresh gasoline), the engine isn't primed (refer to the engine manual), the spark plug is faulty (clean, adjust the gap, or replace it), the fuel line is blocked (clean it), or the engine is flooded (wait a few minutes to restart, without priming).
Why overhead chute crank does not stay stationary while throwing snow using an overhead chute control in MTD Snow Blower?
If the overhead chute crank on your MTD Snow Blower does not stay stationary, there might be insufficient preload applied to the chute control. Refer to the Service section to adjust the chute preload.
Why MTD Snow Blower engine running erratically?
An MTD Snow Blower engine running erratically could be due to: * The engine running on CHOKE. Move the choke lever to the RUN position. * Stale fuel. Replace with clean, fresh gasoline. * Water or dirt in the fuel system. Drain the fuel tank and refill with fresh fuel.
What to do if MTD 500 fails to discharge snow?
If your MTD Snow Blower fails to discharge snow, several issues could be responsible. First, stop the engine immediately, disconnect the spark plug wire, and check for any clogs in the chute assembly. Clean the chute assembly and the inside of the auger housing using a clean-out tool. Also, stop the engine immediately, disconnect the spark plug wire and inspect the auger for any foreign objects and remove them with a clean-out tool. Finally, check the shear pins and replace them if sheared.
What to do if MTD Snow Blower engine overheats?
If your MTD Snow Blower engine overheats, it is possible that the engine oil level is low. Fill the engine with the proper amount of engine oil.
Why MTD 500 unit plows snow instead of blowing it?
Your MTD Snow Blower might be plowing snow instead of blowing it due to low ground speed in wet or slushy snow, or sheared shear pins. Increase the ground speed and always operate the snow thrower engine at FULL throttle. Also, replace any sheared shear pins.
What to do if MTD 500 Snow Blower engine running erratically?
If your MTD Snow Blower engine is running erratically, it might be due to the engine running on CHOKE, stale fuel, water or dirt in the fuel system, a carburetor out of adjustment, or the engine being over-governed. Try moving the choke lever to the RUN position, fill the tank with clean, fresh fuel, or drain the fuel tank and refill it with fresh fuel. For carburetor or over-governed issues, contact an authorized Service Center.
General| Type | Two-Stage |
|---|---|
| Engine Type | 4-Cycle |
| Auger Material | Steel |
| Stages | Two-Stage |
| Engine Displacement (cc) | 179 cc |
| Max Throw Distance (ft) | 40 ft |
| Number of Forward Speeds | 6 |
| Number of Reverse Speeds | 2 |
| Chute Control | Manual |
To Next Page
