MTD Yard-Man 31AE6GLF590

Questions and Answers

B
Brooke MatthewsAug 9, 2025
Why MTD Yard-Man 31AE6GLF590 Snow Blower engine fails to start?
- T
  Travis JonesAug 9, 2025
  Your MTD Snow Blower might fail to start due to several reasons: * The choke might not be in the ON position, so move the choke to the ON position. * The spark plug wire might be disconnected, so connect the wire to the spark plug. * The fuel tank might be empty or contain stale fuel, so fill the tank with clean, fresh gasoline. * The engine might not be primed, so prime the engine as instructed. * The spark plug might be faulty, so clean, adjust the gap, or replace it. * The fuel line might be blocked, so clean the fuel line. * The safety key might not be fully inserted into the ignition, so insert the key fully into the switch. * The fuel shut-off valve might be closed (if equipped), so open the fuel shut-off valve.
A
Andrea RayAug 14, 2025
What to do if MTD Yard-Man 31AE6GLF590 unit fails to discharge snow?
- A
  Alejandro MyersAug 14, 2025
  If your MTD Snow Blower isn't discharging snow, here's what you can do: * The chute assembly might be clogged. Immediately stop the engine, disconnect the spark plug wire, and clean the chute assembly and the inside of the auger housing using a clean-out tool or a stick. * A foreign object might be lodged in the auger. Immediately stop the engine, disconnect the spark plug wire, and remove the object from the auger using a clean-out tool or a stick. * The shear pins might be sheared, so replace them with new ones.
C
Catherine WestAug 19, 2025
Why does my MTD Snow Blower engine run erratic?
- S
  Shannon CastroAug 19, 2025
  An MTD Snow Blower engine might run erratically due to: * The unit running on CHOKE, so move the choke lever to the OFF position. * A blocked fuel line or stale fuel, so clean the fuel line and fill the tank with clean, fresh gasoline. * Water or dirt in the fuel system, so drain the fuel tank and refill it with fresh fuel.
S
Sally HuntAug 25, 2025
What to do if MTD Yard-Man 31AE6GLF590 Snow Blower has loss of power?
- J
  John EstradaAug 25, 2025
  If your MTD Snow Blower is experiencing a loss of power: * Check the spark plug wire and ensure it is connected and tightened. * Inspect the gas cap for any blockages. Remove any ice or snow and ensure the vent hole is clear.
J
Jessica BanksAug 29, 2025
Why MTD Snow Blower has excessive vibration?
- C
  Christina HerringAug 29, 2025
  If your MTD Snow Blower has excessive vibration, it is likely due to loose parts or a damaged auger. Stop the engine immediately, disconnect the spark plug wire and tighten all bolts and nuts.
P
Pamela TannerSep 3, 2025
How to solve the problem when MTD Snow Blower unit fails to propel itself?
- D
  deannamillerSep 3, 2025
  If your MTD Snow Blower unit isn't propelling itself, it could be due to: * The drive control cable needing adjustment. * A drive belt being loose or damaged, so replace the drive belt.

Summary

Safety Labels

WARNING

Explains the meaning and importance of the warning symbol.

Your Responsibility

Defines the operator's responsibility for safe use.

Safe Operation Practices

Training

Provides instructions for safe operation training.

Preparation

Outlines steps for preparing the machine for operation.

Safe Handling of Gasoline

Details safe procedures for handling gasoline.

Operating Your Snow Thrower

Controls Overview

Identifies and describes key controls like levers and knobs.

Shift Lever and Speeds

Explains the function and positions of the shift lever.

Engine Starting Controls

Auger and Drive Controls

Operation of auger and drive engagement controls.

Chute Directional Control

How to operate the chute directional and tilt controls.

Chute Clearing Safety

Engine Starting Procedures

Detailed steps for starting the engine using electric or recoil methods.

Stopping the Engine

Procedures for safely stopping the engine.

Auger Control Test

Procedure to test and adjust the auger control cable.

Maintaining Your Snow Thrower

Engine Maintenance

Lubrication

Details lubrication points like gear shaft, wheels, chute control, auger shaft.

Auger Belt Replacement

Drive Belt Replacement

Off-Season Storage

Storage Preparation

Steps for preparing the snow thrower for long-term storage.

Fuel Handling for Storage

Procedures for draining or stabilizing fuel for storage.

Trouble-Shooting

Engine Fails to Start

Engine Runs Erratic

Engine Overheats

Excessive Vibration

Loss of Power

Unit Fails to Propel Itself

Unit Fails to Discharge Snow

MTD Yard-Man 31AE6GLF590 Specifications

General

Engine	208cc OHV 4-cycle
Clearing Width	26 inches
Intake Height	21 inches
Drive System	Self-propelled
Speed Settings	6 forward, 2 reverse
Stages	Two-stage
Engine Displacement (cc)	208
Auger Material	Steel
Forward Speeds	6
Reverse Speeds	2
Tire Type	X-Trac
Electric Start	Yes
Headlight	Yes
Engine Type	OHV
Chute Control	Crank
Tire Size (in)	15
Starting System	Recoil and electric start