MULTISPAN PID 2303-1C User Manual

PID CONTROLLER
PID 2303-1C
PV = Process value
SV = Set value
INPUT SPECIFICATION:
Input Types
Resolution
Indication
Accuracy
Input Range
0 to 400°CJ
K
J,K = 1°C
±1% of FSD ± 1°C
(FSD:- full scale deflection)
DISPLAY AND KEYS:
CONTROL METHOD:
DIMENSION:
Display
Heating
Size (mm)
Cooling
Alarm
Panel Cutout
Upper: 4 digit, 7 seg 0.56” white LED
1) PID control with Auto-Tuning
Middle: 4 digit, 7 seg, 0.31” green LED
2) ON-OFF control
72 (H) x 72 (W) x 85 (D) mm
68 (H) x 68 (W) mm
TECHNICAL SPECIFICATION
0 to 500°C
Lower: 3 digit, 7 seg, 0.39” red LED
POWER SUPPLY:
ENVIRONMENT CONDITION:
Power Consuption
(VA Rating)
Relative Humidity
Protection Level
Supply Voltage
Operating Temp.
100 to 250V AC, 50-60Hz
0°C to 55°C
UP to 95% RH
(non-condensing)
IP-65 (Front side) As per IS/IEC
60529 : 2001
Approx 6VA @ 230V AC
TERMINAL CONNECTION
MECHANICAL INSTALLATION
1 CT 0.0 to 30.0 A
1) BL.TP ( Blower Time Proportion)
Heater break alarm, Cold start, High,
Absolute low, Inband, Absolute outband
2) ON-OFF control
72
85
68
68
3
72
Outline Dimension (mm)
Panel Cutout
Dimension (mm)
SET
TUNE
OUT1
OUT2
AL
H
PV
SV
ºC
PID 2303-1C
32
4
2
3
5
4
5
1
2
8
9
10
11
12
13
14
L
N
!
H1
RELAY-3
RELAY-1
NO
NO
CT
COM.
RELAY-2
-
+
TC
100
250V AC
~
50/60 Hz
6VA
15
18
16
19
17
20
3
4
5
6
7
NO
S.S.R
-
+
C
NC
C
C
www.multispanindia.com
Made in India
Keys
SET, INC, DEC, ENT
OUTPUT SPECIFICATION:
Relays
Output Signal
Relay Type
Rating
3 Nos
24V DC, 30mA DC
(On-Off condition)
Relay 1 parallel to SSR
st nd rd
1 Relay 1C/O & 2 & 3 Relay (NO-C)
10A,230V AC/28V DC
Relay Output
SSR Drive Output

MULTISPAN PID 2303-1C Specifications

General

Brand	MULTISPAN
Model	PID 2303-1C
Category	Controller
Language	English

Summary

Technical Specifications

Input Specification

Details on input types like J, K, CT, resolution, indication, and accuracy.

Output Specification

Information on relay outputs, relay type, rating, and output signal.

Mechanical Installation

Dimensions for outline and panel cutout, essential for fitting the device.

Operational Overview

Status LED Description

Explanation of the status LEDs (A-E) indicating control output and tuning status.

Key Operation

Guide to using the device's keys for navigation and parameter setting.

Safety and Guidelines

Covers safety precautions, warnings, installation, and maintenance procedures.

Error and Parameter Management

Error Display and Correction

Information on error codes, their meanings, and corrective actions for sensor issues.

Factory Setting Mode

Procedure for accessing and applying factory default settings.

Parameter Message Description

List of parameters with their descriptions and possible values.

Working Modes and Parameter Ranges

Heating and Cooling Modes

Description of PID and ON/OFF control actions for heating and cooling.

Auto-Tuning Function

Explanation of the auto-tuning process for automatic parameter computation.

Parameter Ranges

Defines the configurable ranges for various control parameters.

Parameter Setting Procedures

Set Point and Password Entry

Steps for setting process values, set points, and entering the password.

Configuration Cases

Detailed setting procedures based on selected configuration cases (HBA, CS, HIG, ABL).

Advanced Parameter Configuration

INB, ABO and OFF Select Cases

Parameter settings for INB, ABO, and OFF selection cases.

Control Parameter Settings

Configuration of PID action, proportional band, integral time, and derivative time.

Alarm Operations

Alarm Types and Behavior

Description of Heater Break, Cold Start, High, Absolute Low, and Inband alarms.

Alarm Waveform Visuals

Graphical representation of High, Absolute Low, Inband, and Absolute Outband alarms.