MULTISPAN PTC-1202A-M1 - Page 5

PARAMETER SETTING
ALM1=IN-B,AB-O,OT-B
ALM1=IN-B,AB-O,OT-B
Press key
Press key
Press key
SET
S2MD = INDI
S2MD = INDI
ALM2=IN-B,AB-O,OT-B
ALM2=IN-B,AB-O,OT-B
S1MD = INDI
Process Value
Set Value
S1MD = INDI
SET
SET
Analog O/P = Controlling
/
Analog O/P = Controlling
Password 73 Explanation
RLY 1 / RLY 2
/A.OUT/SOAK/M.BUS
If Auto Mode
Note : In case 4 & 8 relay will be in off condition
If Manual Mode
/
/
/
Parameter 1 : Basic Configuration ( )
Parameter 2 : Relay 1 ( )
Case 1 : Heat
Case 5 : Heat
Case 2 : Cool
Case 6 : Cool
Case 3 : Alarm
Case 7 : Alarm
Case 4 : Off
Case 8 : Off
Parameter 3 : Relay 2 ( )
Parameter 5 : Soak Timer( )
Parameter 4 : Analog Output ( )
Parameter 6 : Modbus ( )
To set Controlling Output Mode press key
SET
+
Case 4 & 8 : OFF
/K/PT/PT.1
/0-10/0-20
/4-20
Input Selectable J/K/PT/PT.1
Return to Parameter Menu
Parameter 1 :
Basic Configuration
( )
IF IN-B
OT-B AB-O
Selected
/
/
/
/
Return to Parameter Menu
Return to Parameter Menu
Return to
Parameter Menu
Return to
Parameter Menu
/
/
/
/
/
/
/ /
Parameter 2 :
Relay 1
( )
Case 1 : Heat
Case 2 : Cool
Case 3 : Alarm
IF IN-B
OT-B AB-O
Selected
/
/
/
/
Return to Parameter Menu
Return to
Parameter Menu
Return to
Parameter Menu
/
/
/
/ /
/
/ /
Parameter 3 :
Relay 2
( )
Case 5 : Heat
Case 6 : Cool
Case 7 : Alarm
/
/
/
/
/
/
/
/
Return to Parameter Menu
Return to Parameter Menu
/
/
/
/ /
/
Parameter 4 :
Analog Output
( )
Parameter 6 :
Modbus Setting
( )
Parameter 5 :
Soak Timer
( )
/ /
CONTROL FUNCTION
HIGH ALARM:
RLY-ON
RLY-ON
RLY-OFF
RLY-ON
RLY-OFF
S.V
HYST
LOW ALARM:
RLY-OFF
RLY-ON
RLY-ON
RLY-ON
RLY-ON
RLY-OFF
RLY-OFF
HYST
S.V
OUTBAND ALARM
RLY-ON
RLY-ON
RLY-ON
RLY-OFF
RLY-OFF
High S.P
Low S.P
ABSOLUTE OUTBAND ALARM
RLY-ON
RLY-ON
RLY-ON
RLY-OFF
RLY-ON
RLY-OFF
RLY-OFF
RLY-OFF
RLY-OFF
High
High
Low
Low
High : 125
Low : 75
INBAND ALARM
RLY-ON
RLY-ON
RLY-ON
RLY-OFF
High
Low
High : 125
Low : 75
ABSOLUTE LOW ALARM
RLY-OFF
RLY-OFF
RLY-ON
RLY-ON
RLY-OFF
SET
HYST
Return to Parameter Menu
Frame Delay
0 to 99