NAD 7100 Series - Receiver Specifications; Power Amplifier Specifications; FM Tuner Specifications; AM Tuner Specifications

Specifications
NAD 7100 Stereo Receiver
Note:
Specifications
are
measured
in
accordancae
with
EIA
Standard
RS-
490
(IHF
A-202)
for
amplifiers
and
ANSI-IEEE
Standard
185
(1975),
i.e.
IHF
T-200,
for
tuners.
Tuner
sensitivity
is
measured
via
75-ohm
coaxial
input.
Ampllifier
measurements
referred
to
8
ohm
are
taken
with
the
Speaker
Impedance
selector
set
to
8
ohm
(High).
Measurements
for
4
and
2
ohm
are
taken
with
lmpedance
selector
at
4
ohm
(Normal).
FM Tuner Section
Input sensitivity
Mono,-30 dB PHDeN 11 dBf(1.0u¥ into 75 ohm}
Mono, 50 dB S/N 14 dBf(1.4u¥ into 75 ohn}
Stereo,50 dB S/N 26 dBf (5.5 uV)
Stereo, 60 dB S/N 37 dBf (20 uv)
Power Amplifier Section
CONTINUOUS AVERAGE POWER
OUTPUT AT 8 OHM (miniaus RWS
power per channel, both channels driven,
with no more than the rated distortion]
Rated distortion (THD), 20 He - 20 kis 0.03%
50 W(17 dB¥)
Clipping power, 1 kHz (maxinua 10 ¥ Capture ratio (at 45 and 85 dBf) © <1.6 dB
continuous power per channel} AM rejection (at 45 and 85 dBf) 60 dB
Dynamic Headroom at 8 cha +6 dB Selectivity,alternate channel 70 dB, IF normal
Dynanic power (maximus 8 ohm 200 W 80 dB, IF narrow
short-term power per channel) 4 obs 250 W Image rejection 80 dB
2 oha 330 # R.F, intermodulation 60 dB
Damping factor 100 IF. rejection 120 dB
Slew factor 50 SCA rejection 10 dB
Slew rate 35V/usec Subcarrier suppression(19, 38 kHz) 65 dB
T.H.D, and SMPTE I.4. distortion from (0.03% THD at 100% modulation Mono, 1 kHz 0.1%
250 aW to rated output Narrow IF 0.5%
IHF IM. (CCIF IM) and T.1.M. distortion 0.03% 100Hs-6kHz 0.2%
at rated output
Input inpedance
10 koha/600pF
Stereo, | kHz 0.1%
Narrow IF 0.5%
Input sensitivity for 1 Watt/50 Watts out 120 wV/8500V 100Hz-Gkiz 60.3%
Power amp gain 27 4B Signal-to-noigse ratio Mono 83 dB
Preaaplifier Section IHF weighted, 65 dBf Stereo 77 dB
Phono Input Frequency reponse, 30Hz-15 kis +0.5 dB
Input Impedance 4M + XC R=47 kohw, C=100 pF Stereo separation 1 kHz 50 dB
Input Sensitivity (1 kHz) MM/MC
MH/HC
Signal-to-Noise Ratio with MM
cartridge connected, A-weighted HC
Input Overload at 20 Hs/ikHz/20kHz MM
HC
RIAA Accuracy
High-Level Inputs (CD, Video, Tape)
Input Impedance
Input Sensitivity
Signal-to-Noise ratio, A-weighted
Input Overload
Frequency Response
Outputs
Preamp output impedance
Tape output impedance
Controls
Treble
Bags
Bass Rqualization
Infrasonic Filter
Low Level (audio auting)
35/.025mV¥ for 1¥ out
2,5/.18aV for 50W out
15 dB re 5 a¥
15 dB re 0.5aV
20/180/1500 aV
1.4/13/100 a¥
+0.5 dB
R=50 kohm, C=500 pF
20 eV for 1¥ out
150 a¥ for 50¥ out
94 dB re 1 W out
{11 dB re 50 ¥ out
>10V
20He-20kH: + 0.508
600 ohe
100 ohn
#9 dB at 10kHz
+10 dB at 50 Hs
+3 dB at 55 as
+6 dB at 36 Hz
-3 dB at 12 HZ
12 dB/octave
20 dB
AM Tuner Section
Usable sensitivity
THD
Selectivity
Image rejection
I.P. rejection
30Hz-10kHz 35 dB
300 uV/aeter
0.5%
35 dB
50 dB
35 dB
S/N ratio(30% mod., 50m input) 45 dB
Physical Specifications
Width x Height x Depth
Net Weight
Shipping Weight
Power Consumption
43.5 x 11x 40 ca,
17.11 4.25 x 19.5 in.
11 kg (24.4 Lbs}
12.7 kg (28.2 lbs}
50/60 Hz at 110,120,
220, or 240 VAC
220 VA
All specifications for A, Al model (US-type, 75 uSec}
; others may vary,